Subscribe to Our Youtube Channel
Related Manuals for Impresind ColdAIR TC123F4
Summary of Contents for Impresind ColdAIR TC123F4
- Page 1 ADIABATIC EVAPORATIVE COOLERS WITH INLET AIR FILTRATION MOD: TC123F4/TC123F9/TC223F4/TC223F9 USE AND MAINTENANCE INSTRUCTIONS STP101.1235- Ed-02-23-USO-SERIE-F...
-
Page 2: Table Of Contents
INDEX GENERAL INFORMATION ..........................3 Preamble ................................. 3 SECTION 1 – CHARACTERISTICS ........................4 1.1 Presentation of the ColdAir Evaporative Cooler ..................4 1.2 Foreseen use ............................4 1.3 Machine identification data ........................5 1.4 Electrical boards ............................5 SECTION 2 – USING THE EVAPORATIVE COOLING UNIT ................5 2.1 First start up .............................. -
Page 3: General Information
GENERAL INFORMATION PREAMBLE Dear Customer, We thank you for choosing an Impresind product and we would like to inform you that: The contents of this document are for information purposes only and are subject to modifica tions without notice;... -
Page 4: Section 1 - Characteristics
It is absolutely forbidden to make modifications to the machine and its destination of use. IMPRESIND SRL declines all responsibility for any damages which may be, directly or indi- rectly, caused to exposed persons or property, due to improper use or use of the machine for... -
Page 5: Electrical Boards
If Technical Assistance or spare parts are required, always supply the machine model and serial number. 1.4 Electrical boards Any electrical boards supplied by Impresind s.r.l. are manufactured according to CEI EN 60204-1:2018 regulations. It is absolutely forbidden to make modifications to the electrical board. -
Page 6: Description Use/Program And Operation
Place a perfectly straight extruded bar on the two pulleys, by using a finger apply a light force on the middle of the belt and measure the distance be- tween the flexed belt point and the bar. The distance should be between 1cm and 1,5cm. -
Page 7: Command Descriptions
2.2.1.1 Controller Description Control Keyboard Pressed once during setting On/off periods, and exits menù. Keeping pressed more than 3 sec. if control unit is loccked , ora temporary unlocked. Displays th current Fan speed (F1,F2,F3, ecc ecc) Pressed once, gets into program selection (PTim menù) or into On/Off periods setting, and it has enter fuction. -
Page 8: Signal Descriptions And On-Screen Displays
2.2.1.2 Signals descriptions and on-screen diplays On-screen displays Signals operations Command/operation running Manual cooling Automating cooling Manual ventilation Automating ventilation Water drain open Water drain closed and water load on Unit off. Attention: the pannel is power on Only ventilation mode Cool Cooling mode Self cleaning... -
Page 9: Settings
2.2.4.2 Automatic start mode With the machine switched on, press key until led of the corresponding automatic mode is 2.2.5 Setting 2.2.5.1 Setting the correct time Keep the key pressed until display shows “Time” On the display shows the setted curent time. When you are modifyng the time the simbol blinking Press the key... -
Page 10: Reading A Stored Program
2.2.5.3 Reading a stored program Press the key and the display will show the first space memory. Repeat the operation to view the next programs Press key for exit 2.2.5.4 Modifyng a program Press the key and the display will show the first space memory. Repeat the operation until view the program to be changed Act on the keys for to modify the program parameters... -
Page 11: Locking/Unlocking Remote Command Unit
2.2.5.7 Locking/Unlocking remote control unit It is possibile to lock or unlock the control unit by changing the “HL” parameter. To change this parameter, proceed as follows: - keep pressed together the keys until the display shows “PA” - press key - press key to find the parameter to be changed (HL) - press key... -
Page 12: Ventilation
disconnect water supply 2.2.8 Bus System The unit is equipped with an electronic interface by bus system and/or network system. Various optionals and alternative control unit are available on the catalog. For more information contact Impresind Srl... -
Page 13: Additional Functions
- 1 - pump switch-off 10 min earlier than the end of the automatic cooling cycle - 2 - pump switch-off 20 minutes earlier than the end of the automatic cooling cycle (parameter recommended by Impresind) - 3 - etc etc ……... -
Page 14: Functioning Notes
2.4 Notes on operation An Evaporative Cooler works on the basis of an important principle: It introduces large quantities of cool air into the environment and removes the warm and stale air through openings (doors, windows, etc.). COLD Air models equipped with inlet air filtration further improve the microclimate of the envi- ronment, by purifying the air before it is cooled and the introduced into the environment. -
Page 15: Pre-Season Maintenance
Before carrying out any maintenance operations, read carefully this section of the manual. For any necessity, contact Impresind Srl After Sales Service. Impresind Srl is not responsible for any damage or malfunctions due to lack of respect of the indications contained in the present section of this manual. -
Page 16: On Board Signs
3.3.4 Technical assistance request For any technical assistance intervention, contact the installer or a licensed technical service center. To know the nearest licensed technical service center, please contact Impresind srl. SECTION 4 – DISMANTLING In case of dismantling and disposal of the plant, all material concerning the plant must be collected and sent to the appropriate collection and disposal centres of companies specialized in the disposal sector. -
Page 17: Wiring Diagram
WIRING DIAFRAM TC123 & TC223... - Page 18 TECHNICAL CHARACTERISTICS Model Air flow Speed min / max V/~Hz Power supply Absorbed current Power consumption Water consumption (*) lt/h (average) Dimensions WxDxH Water supply Diam. Water drain Diam. Air duct dimensions Weight Empty / Full Fan type Max lenght of ducts 5 m + 1 elbow 5 m + 1 elbow 8 m + 1 elbow...
- Page 19 AIR FILTERS - TECHNICAL CARACTERISTICS FILTERS DESCRIPTION PICS THECNICAL DATA Frame: galvanized steel FILTERING-CELLS Filter: synthetic SYNTHETIC ONDULATE Efficency: Eurovent: Arrestance: Max Pressure: 250 Pa Frame: plastic POKET FILTERS Filter:: micro fiberglass IN MICRO FIBERGLASS Efficency: F8-F9 Eurovent: EU8-EU9 ONLY FOR MODELS Arrestance: 90%-95% TC123F9 AND TC223F9...
- Page 20 INFORMATION ABOUT MAINTENANCE: FILTERS AND COOLING PADS REMOVE THE ANTI-RAIN GRIDS BY UNSCREWING THE FIXING SCREWS ALWAYS CHECK THE CORRECT ORIENTATION (see labels on the grids) PULL-OUT THE FILTERS BY REMOVING THE METALLIC CLIPS REMOVE THE TOP COVER BY UNCREWING THE FIXING BOLTS REMOVE THE WATER DISTRIBUTOR PULL-OUT THE COOLING PADS...
-
Page 21: Drawing
DRAWING TC123-F4 TC223-F4... - Page 22 TC123-F9 TC223-F9...
- Page 23 Impresind Srl Via 1° Maggio 24, 20064 Gorgonzola (Milano, Italy) STP101.120 Tel. +39 02 95741932 Fax +39 02 73960191 e-mail impresind@impresind.it www.impresind.it...
Need help?
Do you have a question about the ColdAIR TC123F4 and is the answer not in the manual?
Questions and answers