Related Manuals for SkyLine skyTECH SKY-EL-01
Summary of Contents for SkyLine skyTECH SKY-EL-01
- Page 1 User Instructions Manual skyTECH Universal E-Launcher SKY-EL-01 Skyline Ziplines Ltd. admin@skylineziplines.ca www.skylineziplines.ca...
-
Page 2: Revision History
Revision History Revision Sections Affected Changes Date Original Publication 05 May 2021 Page 2 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 2 of 23... -
Page 3: Table Of Contents
Table of Contents CONTENTS ............................. 2 EVISION ISTORY ............................3 ABLE OF ONTENTS ........................5 ARNINGS AND MPORTANT OTICES DESCRIPTION ............................6 Applications ..........................6 Standards ............................. 6 Description of skyTECH Universal E-Launcher ................6 LIMITATIONS ............................7 Capacity and Working Load Limit ....................7 Environmental Hazards ......................... - Page 4 10.0 INCIDENT AND FAILURE REPORTING ....................16 11.0 WARRANTY............................17 A – I ........................18 PPENDIX NSPECTION B – M ........................20 PPENDIX AINTENANCE C – D ..................22 PPENDIX OCUMENTATION ROCESS LOWCHART Page 4 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 4 of 23...
-
Page 5: Warnings And Important Notices
This manual contains information and instructions specific to the skyTECH Universal E- Launcher and associated equipment manufactured by Skyline Ziplines Ltd. Make sure this User Instructions Manual is the latest version available. Contact Skyline Ziplines to obtain the latest document revisions, important Updates and other notices. -
Page 6: Description
1.0 Description Applications The skyTECH Universal E-Launcher is to be used as a trolley retention and release device for zipline amusement rides. Standards Refer to local, provincial/state and federal laws and regulations pertaining to the installation and use of this type of equipment. Description of skyTECH Universal E-Launcher 1.3.1 skyTECH Universal E-Launcher Clamp Set Product Codes:... -
Page 7: Limitations
2.0 Limitations Consider the following application limitations before using this equipment: Capacity and Working Load Limit ▪ Not to be used in operations exceeding 300 lbs patron weight Environmental Hazards Use of this equipment in areas with environmental hazards may require additional precautions to prevent injury to the user or damage to the equipment. -
Page 8: System Requirements
3.0 System Requirements Compatibility of Components Skyline equipment is designed for use with the Skyline approved components and subsystems only. Substitution or replacements made with non-approved components or subsystems may jeopardize compatibility of equipment and may affect the safety and reliability of the complete system. -
Page 9: Nomenclature And Assembly
4.0 Nomenclature and Assembly Description of Parts Page 9 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 9 of 23... -
Page 10: Procedure For Assembling Universal E-Launcher
Procedure for Assembling Universal E-Launcher Tools Required: (2) 7/16” Sockets, (1) 3/8” Socket, (2) Socket Wrenches, (1) 5/32” Allen Wrench *Skyline Ziplines recommends utilizing an anti-seize compound on all stainless-steel components 4.2.1 Remove bolts from cable clamp module. 4.2.2 Install cable clamp module on cable with longer half on bottom with excess facing downhill. -
Page 11: Standard Operating Procedures
5.0 Standard Operating Procedures The following operating procedures outline only the necessary steps required to complete each process. The procedures do not consider additional safety requirements and additional safety considerations that should be considered for each site. Please consult a qualified person and/or your site-specific manual to ensure all necessary steps are taken to guarantee safety in your operations. -
Page 12: Training
Gaining an adequate education in proper techniques and methods of safety is your own responsibility. Training should be done under the supervision of competent persons. It is recommended that Skyline Ziplines perform a manufacturer’s training session to cover the material in this document, use with other equipment, and site specific training. -
Page 13: Inspection
Documentation Process Located in Appendix A is a sample Inspection form that Skyline Ziplines recommends using as a template. Located in Appendix B is a sample Maintenance form that Skyline Ziplines recommends using as a template. -
Page 14: Maintenance And Storage
Thoroughly inspect all equipment after extended storage Replacement Parts and Repairs All replacement parts must be purchased through Skyline Ziplines Ltd. All equipment repairs must be performed by the following: Skyline Ziplines Ltd, an authorized contractor/vendor of Skyline Ziplines Ltd with approval, or trained and authorized onsite personnel. -
Page 15: Universal E-Launcher Maintenance - Replacing Linear Actuator
8.4.4 Re-install the ¼” x 1-3/4” into the retention flap, rotating arm, and spring. Fasten with a washer and locking nut. 8.4.5 Connect the rotating arm on the end of the extension and pull arm, re-installing the two 1/4” x 1-1/4” screws, washers, and nuts. 8.4.6 Check that the E-Launcher retention flaps open and close freely. -
Page 16: Lifetime
Complete information concerning the incident (date, location, details as to event and consequence, etc.) must be communicated to admin@skylineziplines.ca and/or called in to the office at 604-905-4149. Skyline Ziplines will investigate the incident and if a product recall alert is required, shall notify all known customers and distributors who have purchased the product. - Page 17 6-1006 LYNHAM ROAD WHISTLER, BRITISH COLUMBIA, CANADA V8E 0S3 Skyline Ziplines LTD will use reasonable commercial efforts to return all product in a timely manner to the designated location and will be responsible for all shipping costs. Skyline Ziplines LTD reserves the right to modify this limited warranty at any time, in its sole discretion.
- Page 18 Appendix A – Inspection Form *Sample files available upon request This Page Is Intentionally Blank Page 18 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 18 of 23...
- Page 19 Page 19 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 19 of 23...
- Page 20 Appendix B – Maintenance Log *Sample files available upon request This Page Is Intentionally Blank Page 20 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 20 of 23...
- Page 21 Verdict (Circle One): FIT UNFIT RETIRED Page 21 of 23 Unit ID: Performed By: Date: Version: Work Performed: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 21 of 23 Verdict (Circle One): FIT UNFIT RETIRED Form M-13 - Skyline Ziplines LTD -...
- Page 22 Appendix C – Documentation Process Flowchart Documentation Flowchart - Equipment Daily Trained Staff – Daily Inspections Inspection Resolve Issue Can Issue Place Equipment Does Print Inspection Inspect Piece of Lock Out/Tag Out Record On Equipment In Designated Resolved Form Equipment Equipment Inspection Form Pass?
- Page 23 Skyline Ziplines Ltd. Headquarters 6-1006 Lynham Road Whistler, British Columbia Canada V8E 0S3 Canada Phone: (604) 905 - 4149 admin@skylineziplines.ca www.skylineziplines.ca Page 23 of 23 Version: USER INSTRUCTIONS MANUAL – UNIVERSAL E-LAUNCHER Page 23 of 23...
Need help?
Do you have a question about the skyTECH SKY-EL-01 and is the answer not in the manual?
Questions and answers