Table of Contents
Advertisement
Quick Links
USER GUIDE
LOGIC AIR MONOBLOC HEAT PUMP SYSTEM
When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance
specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal Heating.
For the very latest copy of literature for specification and maintenance practices visit our website idealheating.com
where you can download the relevant information in PDF format.
08 / 2023
UIN 235468 A05
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for IDEAL Logic
Summary of Contents for IDEAL Logic
- Page 1 When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal Heating.
-
Page 2: Table Of Contents
Ideal Heating is a member of the Benchmark scheme and fully supports the aims of the programme. Benchmark has been introduced to improve the standards of installation and commissioning of central heating systems in the UK and to encourage the regular servicing of all central heating systems to ensure safety and efficiency. -
Page 3: Introduction
Presence of Frozen Condensate in Walkways: The Logic Air Domestic Hot Water cylinder is to be used to store There is condensate produced by the Heat Pump which can heat from the Heat Pump. The DHW cylinder is to be installed potentially build up around the heat pump and freeze if not within a domestic household. -
Page 4: General Information
• The area directly around the Logic Air Control Box should The circuit consists of four main components/functions. be kept clear at all times. Items such as wet laundry should not be placed upon the control box and general clearances Evaporator Heat Exchanger - Refrigerant absorbs heat illustrated within the Installation Manual must be respected. -
Page 5: Basic Logic Air Functions
60°C for a period of 1 hour. operation may then resume. Note: The backup heater utilised Logic Air Monobloc ASHP Defrost Method: in this mode will depend upon the system configuration (refer During operation, the Heat Pump will periodically be required to Section 2.7.6 Cold Start Function on page 22 for available... -
Page 6: Basic Logic Air Controller And Display Functions
User's BASIC LOGIC AIR CONTROLLER AND DISPLAY FUNCTIONS The Heat Pump controls are located on the front of the control STATUS SYMBOLS box. This is the centralised control for the full heating system. Symbol 'Alarm' indicates a plant error. ⓘ... - Page 7 SETTING THE CENTRAL HEATING TIME PROGRAM The Space Heating function will be controlled via the use of a On/Off non-programmable room stats only Logic Halo Air or equivalent Programmable Room Thermostat 08:32 (PRT). ON/OFF Room Thermostats are not recommended to be...
- Page 8 User's SETTING TIME/DATE SWITCHING THE DHW IMMERSION HEATER ON 08:32 08:32 Primary flow temp 20.0ºC Primary flow temp 20.0ºC Hot water temp 20.0ºC Hot water temp 20.0ºC Outside temp 3.1ºC Outside temp 3.1ºC Primary water flow 0l/min Primary water flow 0l/min Compressor Compressor...
-
Page 9: Logic Air Alarms
User's LOGIC AIR ALARMS CHANGING THE COMFORT SETPOINT 08:32 Any active faults will be displayed on the home screen. Primary flow temp 20.0ºC A bell icon will display in the upper part of the control screen. Hot water temp 20.0ºC... -
Page 10: Fault Codes
User's FAULT CODES Fault ID No. Fault Description Outside Sensor Fault Header Thermistor Fault Flow Thermistor (Indoor) Fault Return Thermistor Fault DHW Thermistor Fault Room Stat 1 Fault Room Stat 2 Fault LPB short-circuit/comm Fault LPB address collision Fault BSB short circuit Fault BSB address collision 2 clock time masters Fault Clock without backup Fault... -
Page 11: Troubleshooting
Heat turned ON Heater is if any there Pump and turned ON are active Back up faults on the Heater is Logic Air turned ON Check the Controller Check the Logic Air Logic Air Controller Check the Controller... -
Page 12: 10. Warranty
User's 10. WARRANTY At the end of each 12-month period after commissioning, the Heat Pump must be serviced by a suitable competent heat pump engineer in accordance with the process in the manufacturer’s instructions. Should this condition not be met the Heat Pump warranty will lapse. - Page 14 At Ideal Heating we take our environmental impact seriously, therefore when installing any Ideal Heating product please make sure to dispose of any previous appliance in an environmentally conscious manner. Households can contact their local authority to find out how.
Need help?
Do you have a question about the Logic and is the answer not in the manual?
Questions and answers