Hide thumbs Also See for QX18i:

Advertisement

Quick Links

PX/QX System
Version 4
Installation Manual
Issue A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QX18i and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Guardall QX18i

  • Page 1 PX/QX System Version 4 Installation Manual Issue A...
  • Page 2: Table Of Contents

    PX/QX Version 4 Installation Manual – Issue A Contents CONTENTS ............................2 STATUTORY REQUIREMENTS ......................4 SUITABILITY FOR USE ........................4 EN50131 & PD6662 COMPLIANCE ...................... 4 CE DECLARATION ..........................5 INTRODUCTION............................. 5 GETTING STARTED ..........................6 ..............................7 AINS ............................
  • Page 3 PX/QX Version 4 Installation Manual – Issue A ...........................29 DDRESS ELECTION PCB C ..........................29 ONNECTIONS OUTPUT MODULE..........................30 MIMIC MODULE ...........................31 SERIAL MODULE ..........................32 DATA COMMS MODULE........................33 KEYPAD ...............................34 BUS ISOLATOR ...........................35 PCB C ..........................35 ONNECTIONS ACCESS MODULE..........................36 PROXIMITY READER ..........................37 ..............................38 AUDIO MODULE ..........................39 RADIO MODULE ..........................40...
  • Page 4: Statutory Requirements

    PX/QX Version 4 Installation Manual – Issue A STATUTORY REQUIREMENTS Hereby Guardall declares that the QX18i and the QX34i are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. If you have any doubts concerning the suitability, connection or uses of this apparatus then consult a suitably qualified person before continuing.
  • Page 5: Ce Declaration

    Guardall manuals, can be downloaded from the Guardall web site at, www.guardall.co.uk The documentation section of the Guardall web site is password protected, and you may have to apply for access using the on-line form provided on the site. Alternatively a printed copy of the manual may be obtained by sending a FAX or letter to our Customer Helpline, requesting the full Engineering Manual.
  • Page 6: Getting Started

    Press 01 to set the keypad address to 1, then press to confirm 00:00 Sat 02 Jan The keypad will then display the time/date and company name. Guardall PX KP Type-n If the displayed message is as shown, or no bleep is heard, then the Version 2.00 keypad is not responding so check the bus connections.
  • Page 7: Mains

    Aux. DC Supply The DC supply output is a Safety Extra-Low Voltage (SELV) circuit. This DC supply rating is for all the DC current requirements, including recharging the battery. The supply has the following rating: Item QX18/QX18i QX34/QX34i PX 18 PX 34...
  • Page 8: Order Codes

    W76203 PX250 High Security Control Output (Plastic) panel (English) v4 W74481 Universal 4 relay output board W74427 QX18i Control panel (English) v3 W76057 Smart Concentrator (8 input/4 W74489 QX18 Control panel (English) v3 output) W76005 QX34i Control panel (English) v3...
  • Page 9: System Components

    PX/QX Version 4 Installation Manual – Issue A System Components A system comprises of the following components: 1. A control unit, which processes all the alarm information from the detection points. Outputs are provided to operate sounders, strobe and communication devices. Configuration information is stored in EEPROM.
  • Page 10 XiB Bus per module Audio Bus Interface Output Mimic Radio Data Concentrator Audio Module Module Module Comms QX18i/34i Module RS232 Tamper GuardStation / Printer QX18i - 5 TX outputs RS232 or Serial QX34i - 8 TX outputs 10 -...
  • Page 11 PX/QX Version 4 Installation Manual – Issue A Radio Smart Access Module Module Access Aux PSU 1.7km (unscreened cable) 1.7km 1.7km Sounder XiB Bus External bus Strobe Isolator Isolator Output Mimic Audio Concentrator Serial Access Module Module Module Module PX18 Refer to PX34 Tamper...
  • Page 12 PX/QX Version 4 Installation Manual – Issue A Radio Smart Access Module Module Access Aux PSU 1.7km (unscreened cable) 1.7km 1.7km XiB Bus 1 Bus 1 Isolator Isolator Output Mimic Concentrator Serial Access PSTN/ Module Module PX80 Bus 2 Module Module Module PX500...
  • Page 13: Technical Specification

    PX/QX Version 4 Installation Manual – Issue A Technical Specification Technical Specification Environmental Parameter Range Temperature range -10 to 50 °C Humidity 10% to 90% relative humidity Technical Specification Cable Type The system has a 4-wire bus for all peripherals. The recommended cable type is 7-strand/0.2mm diameter un-screened cable, which has a resistance of 90 ohms/km and a core to core capacitance of 85nF/km.
  • Page 14: Current Consumption

    PX/QX Version 4 Installation Manual – Issue A Technical Specification Current Consumption Product Current (mA) PX 18 PX 34 PX 80 PX 500/HS QX panel Keypad (standard) Keypad with proximity Concentrator Output module 22 (all relays off) Serial module SmartDial Super (PX) SmartDial Speech SmartDial Speech ISDN Access module...
  • Page 15 PX/QX Version 4 Installation Manual – Issue A The power supply standby capacity specified in PD6662:2004 is shown in the table. Grade Standby time (hours) The following tables show the maximum available system current with a minimum of 12 hours standby for each combination of power supply and battery size.
  • Page 16: Eol Resistor Connections

    Detector EOL Network with Fault The EOL resistors are fitted in the detector as shown. Note that the Guardall V12-AM detector has the necessary 3 EOL resistors fitted on board. For full information refer to the V12- AM manual. Aux.
  • Page 17: Diagnostics

    PX/QX Version 4 Installation Manual – Issue A Diagnostics Diagnostics Accuracy The accuracy of the diagnostic system is typically less than 1%, with a maximum error 2.5%. This accuracy can only be achieved by programming the correct value of the 5V-reference voltage (option 69 on the main menu).
  • Page 18: Qx18/18I Control Unit

    8R2 1/2W resistor must be connected in series Red LED: Dialler in use * Only used by 3rd party communicator Comm fail* Line fault* Dialler (QX18i only) Output 5 Output 4 Output 3 Output 2 Output 1 Tamper TAMPER...
  • Page 19: Qx34/34Icontrol Unit

    PX/QX Version 4 Installation Manual – Issue A QX34/34iControl Unit PSTN Green LED: PTT Line OK If an 8 ohm loudspeaker is Dialler used an 8R2 1/2W resistor must be connected in series Red LED: Dialer in use * Only used by 3rd party communicator Output 8 Output 7...
  • Page 20: Px 18 Control Unit

    PX/QX Version 4 Installation Manual – Issue A PX 18 Control Unit PX 18 Control Unit Installation The PX18 control panel is supplied with a spares bag containing the following items: • Battery lead • Cable clamp • 2.5A fuse •...
  • Page 21: Pcb Connections

    PX/QX Version 4 Installation Manual – Issue A PX 18 Control Unit PCB Connections Tamper Line fault 16Ω 5 volt reference Cct 8 Cct 7 Cct 6 Cct 5 Cct 4 Cct 3 Cct 2 Cct 1 Aux d.c. via FS2 Aux d.c.
  • Page 22: Px 34 Control Unit

    PX/QX Version 4 Installation Manual – Issue A PX 34 Control Unit PX 34 Control Unit Installation The PX34 control panel is supplied with a spares bag containing the following items: • Battery lead • Cable clamp • 315mA fuse •...
  • Page 23: Pcb Connections

    PX/QX Version 4 Installation Manual – Issue A PX 34 Control Unit PCB Connections LK22 Tamper (Tamper Disable) Comm fail Line fault 16Ω Output 2 Output 1 5 volt reference Cct 8 Cct 7 Cct 6 Cct 5 Cct 4 Cct 3 Cct 2 LK15...
  • Page 24: Px 80/500/Hs Control Unit

    PX/QX Version 4 Installation Manual – Issue A PX 80/500/HS Control Unit PX 80/500/HS Control Unit Installation The PX 500 control panel is supplied with a spares bag containing the following items: • Battery lead • Cable clamp • 2.5A fuse •...
  • Page 25: Pcb Connections (Px80)

    PX/QX Version 4 Installation Manual – Issue A PX 80/500/HS Control Unit PCB Connections (PX80) All PCB connections are plug-on screw down terminal blocks. The function and position of each terminal is described in the following page. Case LK7: Fit link to Tamper disable tamper Tamper...
  • Page 26: Pcb Connections (Px500/Hs)

    PX/QX Version 4 Installation Manual – Issue A PX 80/500/HS Control Unit PCB Connections (PX500/HS) All PCB connections are plug-on screw down terminal blocks. The function and position of each terminal is described in the following page. Case LK7: Fit link to Tamper disable tamper Tamper...
  • Page 27: Input Concentrator

    PX/QX Version 4 Installation Manual – Issue A 8 Input Concentrator Address DIL Switch Outputs 3&4 of 4-output concentrator may only be 6 5 4 3 2 1 programmed on a contol panel fitted with version 3.10 or later. 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 1 1...
  • Page 28: Smart Concentrator

    PX/QX Version 4 Installation Manual – Issue A Concentrator Smart Concentrator The smart concentrator includes a standard concentrator PCB and a power supply PCB. Only the power supply PCB is shown in the diagram. To concentrator The Smart Concentrator 0V connection Black must be connected to the PX panel.
  • Page 29: Single Detector Interface

    PX/QX Version 4 Installation Manual – Issue A Single Detector Interface The Single Detector Interface (SDI) is used to connect a detector to the PX XiB bus. A SDI may be fitted inside the following Guardall detectors: • • V12AM •...
  • Page 30: Output Module

    PX/QX Version 4 Installation Manual – Issue A Output Module Address DIL Switch 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 1 1 0 0 0 1 0 0 0 0 0 1 0 1 0 0 0 1 1 0...
  • Page 31: Mimic Module

    PX/QX Version 4 Installation Manual – Issue A Mimic Module Address DIL Switch The mimic module has 24 individual circuit outputs available on the D type connector. The outputs are 6 5 4 3 2 1 multiplexed low current outputs and are only suitable for 0 0 0 0 0 0 connection of an LED.
  • Page 32: Serial Module

    PX/QX Version 4 Installation Manual – Issue A Serial Module Engineer Keypad Address DIL Switch RX V+ 0v TX 8 7 6 5 4 3 2 1 X X X X 0 0 0 0 Tamper X X X X 0 0 0 1 disable A serial module can be added at any time to a...
  • Page 33: Data Comms Module

    PX/QX Version 4 Installation Manual – Issue A Data Comms Module Address DIL Switch 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 The data comms module address can be set to 1 or 2 only.
  • Page 34: Keypad

    PX/QX Version 4 Installation Manual – Issue A Keypad To set the keypad address, open the case so Buzzer that the case tamper switch is activated. Then hold the help button (?) until the address prompt is displayed (approximately 4 seconds). Enter the chosen address using the numeric Proximity Reader keys.
  • Page 35: Bus Isolator

    PX/QX Version 4 Installation Manual – Issue A Bus Isolator The XiB bus isolator can be used to both extend the maximum XiB cable length and to electrically isolate parts of the bus. The maximum bus extension will depend on the cable type and the supply voltage.
  • Page 36: Access Module

    Reader supply voltage Blue, DATA 1/Data 1 1 0 1 0 - Select 12v for Orange, DATA 0/Clock 1 1 0 1 1 Guardall readers. 1 1 1 0 0 1 1 1 0 1 Engineer 1 1 1 1 0 Keypad...
  • Page 37: Proximity Reader

    PX/QX Version 4 Installation Manual – Issue A Proximity Reader The Proximity Reader is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Whilst it operates on a non-harmonised frequency of 125KHz, it meets all relevant harmonised standards. It has been notified in the following EU countries: Belgium, Italy, France, The Netherlands, Denmark, Finland, UK, Ireland, Germany, Spain, Portugal, Norway, Greece and Sweden.
  • Page 38: Leds

    PX/QX Version 4 Installation Manual – Issue A Proximity Reader LEDs Function Red LED Green LED Door LOCKED Door UNLOCKED INVALID card, Flash for approximately 2 Access DENIED or seconds Access ACCEPTED but door not opened. Access ACCEPTED, ON (when door open and Area not in alarm locked, flash on for 1 second) Access ACCEPTED,...
  • Page 39: Audio Module

    PX/QX Version 4 Installation Manual – Issue A Audio Module External microphone connections Address DIL Switch 5 4 3 2 1 0 0 0 0 0 - IP2 + SW - IP3 + SW - IP1 + SW 0 0 0 0 1 0 0 0 1 0 Speaker 0 0 0 1 1...
  • Page 40: Radio Module

    PX/QX Version 4 Installation Manual – Issue A Radio Module The radio module is fitted with 2 PCBs; a RF module and a serial interface for connection to the control panel XiB bus. The serial interface PCB is multi-function and for operation as a radio interface DIL switches 6 and 8 must be on and DIL switch 7 off.
  • Page 41: Gsm/Dual Comm Module

    BS EN60950:2002 - Safety of information equipment Introduction The Dual Comm module, GSM module and the PSTN module may be used with any Guardall control panel that supports the SmartDial Super. This includes any version of PX or QX but excludes QXi variants.
  • Page 42: Installation

    PX/QX Version 4 Installation Manual – Issue A recognised from panel v4. If the GSM/Dual comm module used with earlier panel versions it is recommended that line fault monitoring is enabled to act as a substitute for the tamper sensing. 2.
  • Page 43: Leds

    PX/QX Version 4 Installation Manual – Issue A LEDs Function Colour State Meaning XiB Comms Green No power Communication error Slow FLASH Operating normally Quick FLASH Active Hook Line seized Line monitor Green Valid Exchange voltage level present GSM Status Yellow Quick flash Network search...
  • Page 44 Guardall Limited Lochend Industrial Estate Newbridge Edinburgh EH28 8PL Tel: 0131-333-2900 FAX: 0131-333-4919 www.guardall.co.uk Technical Hotline: 0131-333-3802 Part Number: 320994-0A...

This manual is also suitable for:

Qx34iQx18Qx34Px18Px34Px80 ... Show all

Table of Contents