Advertisement
Quick Links
Advertisement
Related Manuals for Mofi MasterDeck
Summary of Contents for Mofi MasterDeck
- Page 2 Inside Front Cover...
- Page 3 35 years building your ideas into cost- no-object turntables. Could you design a high- value turntable with those ideas?” The answer is MasterDeck. It represents all the principles for platter bearings, drive systems, tonearm concepts, and material combinations that I’ve developed over the past few decades.
-
Page 4: Important Safety Instructions
7. Water and moisture: Do not use MasterDeck near water. vice technician uses replacement parts specified by the manufacturer. Unautho- 8. Accessories: Do not place MasterDeck on an unstable cart or stand. It may rized substitutions may result in fire, electric shock, and other hazards. - Page 5 In the Box 1. MasterDeck Turntable 7. Power Supply 2. Record Spindle & Screws 8. AC Cable 3. Platter with Installation Strap 9. Tone Cable Arm 4. Tone Arm 10. Hex Wrench 5. Turntable Belt 11. Accessory tube 6. Tone Arm Cable Strap &...
-
Page 6: Platter Installation
Platter Installation The upper and lower bearing halves of MasterDeck are capped to seal in lubricant during shipping. Remove both caps. Avoid dripping excess lubricant on your hands and surfaces. Using the installed strap, lift and carefully lower the platter onto the lower bearing. - Page 7 Installing Spindle and Turntable Belt Remove the platter strap. Install the record spindle using the three included screws. Warning: Over-tightening the screws may strip the threads in the Delrin platter surface. Install the turntable belt with the belt attached to the pulley.
- Page 8 Tone Arm Installation Place the tonearm in the base, aligning the slot with Pin 1. Tighten Screw 2 to secure the tonearm in the base.
- Page 9 Tone Arm Cable Plug in the tonearm cable, aligning the slot with the pin. Install the cable strap with the include screw. Route the cable through the rear strap.
-
Page 10: Leveling The Turntable
Leveling the Turntable The playing location should be level and capable of supporting approximately 40lbs. Once MasterDeck is in its intended location, place a bubble level on the platter and level the turntable by carefully turning the appropriate foot. -
Page 11: Power Supply
Power Supply Connect the power supply to MasterDeck. Connect the AC cord to the power supply brick. Connect the AC cord to any outlet or power conditioner. Power off your phonostage (not included) and connect the RCA plugs to the... - Page 12 The first time it powers up, MasterDeck will go CALIBRATI ON through a calibration process and power down. You can then power MasterDeck back on and it will be ready to play at 33.3 rpm. 45 and 78 rpm will calibrate individually on first selection. If AC power is disconnected, calibration will repeat on the first 3 3 .3...
-
Page 13: Cartridge Installation
Cartridge Installation If a cartridge is not included, follow the cartridge manufacturer’s installation instructions. If your MasterDeck came with a preinstalled cartridge, these settings were completed at the factory. Setting Azimuth, Overhang, and Zenith Loosening the headshell screw allows the headshell to rotate for azimuth adjustment. - Page 14 Setting Tracking Force and VTA Adjust the tracking force by rotating the knurled nut. Moving the nut toward the cartridge increases the tracking force; moving the nut away from the cartridge decreases the tracking force. Adjust vertical tracking angle DOWN (VTA) by loosening the screw on the base and moving the nut up and down.
- Page 15 Setting Anti-Skate Adjust anti-skate force by moving the weights. Movement toward the tonearm decreases force; movement away from the tonearm increases force.
- Page 16 Power consumption <5W Dimensions W 20in. H 5.125in. (~ 6.250 with tone arm.) D 15.125 including AC cable Weight 37.4 Lbs MasterDeck™ Tone Arm - Specifications Type: Unipivot/Gimbal hybrid Arm Tube: Straight Damped Carbon fiber Pivot to Stylus distance 10” (254mm)
- Page 17 Inside Back Cover...
- Page 18 MoFi Electronics – 1811 W Bryn Mawr Ave Chicago IL...
Need help?
Do you have a question about the MasterDeck and is the answer not in the manual?
Questions and answers