Advertisement
Maintenance and care
Strainers ...
Rotate filter
cylinder, remove
Check, if
filter system ...
required, clean
Spray arms ...
Pull lower arm
upwards ...
Remove
blockages/deposits
Eliminating minor faults yourself ...
Fault
Possible Cause
Display in wrong language
Language changed
Residual water in the device
Waste-water pump blocked
Programme does not start,
Programme has not been started
does not run on
Door was opened before end of
programme
Device does not work/stops
Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Plastic parts / parts of
Too little cleaning product
dishes discoloured
Discoloration caused by food colourings
(tomato sauce)
Interrupting the programme ...
–
Open the door.
–
To continue the programme, close the door.
For perfect rinsing results ...
rinse under
flowing water ...
Unscrew upper
arm ...
... Self-help pays!
Remedy
Switch off and on the device. Press the
button M/OK repeatedly until the display
shows the language selection. Select
the language using –/+, and store the
selection using M/OK.
Clean waste-water pump (see above)
If necessary, start programmes.
Close the door. Wait for programme stop
(buzzer sounding 5 times).
Open supply fitting.
Lay supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min when
the water inlet is open.
If the flow rate is less, replace the
supply fitting.
Follow manufacturer's specifications
(detergent).
Discoloration is quite safe; fades after
subsequent rinse cycles.
Terminating the programme ...
–
Open the door and press the "Terminate programme" button.
–
Close the door and wait until the buzzer is emitted 5 times.
–
Restart the programme or switch off the appliance.
Insert ...
Clean spray nozzles
Insert lower arm ...
under flowing water
(perhaps with
toothpick) ...
Fault
Possible Cause
Dishes not clean
Utensils are situated too close to each
other or on top of each other
Sand or grainy residues
on dishes
Too little cleaning product
Unsuitable programme selected
Spray nozzles blocked
Filters dirty, not installed securely
Spray arms blocked
Stains and streaks
Rinse aid dosage too high / too low
Milky residues on dishes
Water softening system incorrectly set;
(can be removed)
no special salt
Milky film, glasses cloudy /
Glasses not dishwasher-proof.
dull (cannot be removed)
Cutlery rusty
Cutlery not rust-proof
Hard knife blades are more susceptible
Extraneous rust
Arranging utensils correctly ...
Arrange dishwasher-proof utensils (having removed any ash, wax, grease or ink. Coarsely remove
sticky labels, large remnants of jam, milk products or food) according to the operating instructions
and check that the spray arms can rotate freely.
Cleaning the waste-water pump *
* With some models
Screw in filter
– Ladle out water and remove filters
system NOTE
– Unscrew cover (Torx T20)
MARK!
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Screw in upper arm
Remedy
Spread out the utensils, avoid contact
between the utensils.
Follow manufacturer's specifications
(detergent).
Select more intensive programme.
Clean spray arms (see above).
Clean the strainers (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Streaks: Reduce dosage.
Water or limescale stains:
Increase dosage.
Set water softening system correctly.
Refill with special salt.
Use dishwasher-proof glasses.
Use glass-friendly cleaning products.
Use dishwasher-proof cutlery.
Never wash rusting parts in the
appliance.
Further advice can be found in the instruction manual
Advertisement
