Tempo myAquaSolar user guide CONTENT PAIRING page FIRST OR NEW START-UP page INSTALLATION page RAIN SENSOR page TIMER STATUS page TIMER STATUS - Bluetooth® signal page TIMER STATUS - Energy level page ACTIVATING/DEACTIVATING AUTOMATIC WATERING page SETTING A PROGRAMME page...
You must have installed the myAquaSolar app on your smartphone in order to start using the product. The myAquaSolar app is available on Google Play® and the App Store®. EN - 2 Tempo myAquaSolar - cod. 8497...
Page 3
Enter the numerical code (PIN) or scan the QR code. This information is on the back of the control unit: disconnect it from the timer to The timer profile will appear on the access it. main page of the app. N.B. the myAquaSolar app can manage up to 4 timers. Tempo myAquaSolar - cod. 8497 EN - 3...
To make sure it has the timer with the photovoltaic panel positioned in direct sunlight. the right charge before using it, check exposed to direct sunlight. the energy level icon. EN - 4 Tempo myAquaSolar - cod. 8497...
Page 5
(from 30 to been disconnected. The timer can now 90 minutes depending on how strong be used. the light is). No watering cycle can be set until the FIRST OR NEW START-UP is finished. Tempo myAquaSolar - cod. 8497 EN - 5...
Do not use the water timer with chemicals or liquids other than water. Do not use the water timer with operating pressures lower than 0.5 bar (7.3 psi) or higher than 10 bar (145 psi). EN - 6 Tempo myAquaSolar - cod. 8497...
Page 7
INSTALLATION Remember to open the tap and close the timer cover. Tempo myAquaSolar - cod. 8497 EN - 7...
RAIN SENSOR 90915 CRACK! Tempo myAquaSolar can be used with With the help of small pliers, break the Remove the bridge connector on the Insert the Rain Sensor connector. The the wired Claber Rain Sensor (code plastic plug for preparing the slot of timer.
Page 9
If the symbol is blue but the Rain Sensor has not been installed, check that the jumper has been inserted correctly. Tempo myAquaSolar - cod. 8497 EN - 9...
Bluetooth® signal, energy about the timer status by selecting the level, solar radiation and Rain Sensor. timer profile and looking at the top Select an icon to find out what it toolbar. means. EN - 10 Tempo myAquaSolar - cod. 8497...
If the situation persists and during PAIRING the PIN was entered without using the QR code, it is possible that the wrong code has been entered. Delete the timer and try the PAIRING process again. Tempo myAquaSolar - cod. 8497 EN - 11...
16 time and, after checking that the hours before the timer turns off. Bluetooth® icon is blue, press the product profile in the app. EN - 12 Tempo myAquaSolar - cod. 8497...
LED; the automatic watering off product profile. If automatic watering is not on, the red status through the flashing red LED. symbol will show on the picture of the timer. Tempo myAquaSolar - cod. 8497 EN - 13...
SETTING A PROGRAMME Tap the timer profile to start Tempo myAquaSolar offers 2 irrigation Press Start time. Scroll through the hours and minutes programming. programmes, A and B. Select the until you reach the time you want desired programme. to start the irrigation cycle at and confirm.
Page 15
Watering can be set from run. Watering will take place on the that the programme’s toggle button 1 minute to 3 hours and 59 minutes. days shown in orange. is On. Tempo myAquaSolar - cod. 8497 EN - 15...
Page 16
Press Save and go back to confirm the For the watering cycles set to take settings entered. place, make sure that the automatic Note: the programmes cannot watering toggle button is On. overlap. EN - 16 Tempo myAquaSolar - cod. 8497...
MODIFYING A PROGRAMME Select the programme that you want Change the settings you want. Press Save and go back to make the to modify on the timer profile. modifications effective. Tempo myAquaSolar - cod. 8497 EN - 17...
Watering can be set from 1 minute to 3 hours and 59 minutes. EN - 18 Tempo myAquaSolar - cod. 8497...
Page 19
STOP. Once manual irrigation is complete, the timer returns to the automatic watering active status. If an automatic watering cycle is scheduled during a manual watering cycle, it will not run. Tempo myAquaSolar - cod. 8497 EN - 19...
AUTO AUTO To activate manual watering from the timer, repeatedly press the Tempo myAquaSolar To pause it before it is finished, repeatedly press the timer key to set the desired status: button until the LED flashes green. In this case, manual irrigation will run for 15 minutes.
To give a name to the timer or the irrigation line, press the modification icon for the or to its irrigation lines from the desired section. Enter the text and confirm. myAquaSolar app. Open the myAquaSolar app menu. Tempo myAquaSolar - cod. 8497 EN - 21...
Note: a timer deleted from the app continues the automatic watering cycles set but will no longer appear on the app’s main screen. If you only want to pause the programmed watering cycle, press the automatic watering toggle button. EN - 22 Tempo myAquaSolar - cod. 8497...
Never carry out a reset when the timer is watering: the flow of water might not stop. To reset the timer, hold down its button for 20-30 seconds, until the LED stops flashing. Tempo myAquaSolar - cod. 8497 EN - 23...
Rinse the filter clean under running season and check it regularly. water. After washing, reassemble all parts as before. Turn off the tap and loosen the tightening ring nut by turning it clockwise. EN - 24 Tempo myAquaSolar - cod. 8497...
The Bluetooth® brand and logo are registered trademarks owned by Bluetooth SIG, Inc. and are used under licence by Bluetooth SIG, Inc. Claber S.p.A. does not claim any right over the third-party trademarks listed. At the end of the season, before the...
Need help?
Do you have a question about the Tempo myAquaSolar and is the answer not in the manual?
Questions and answers