Subscribe to Our Youtube Channel
Related Manuals for PK Grills Original PK300AF
Summary of Contents for PK Grills Original PK300AF
- Page 1 A SSEMBLY INS T RUCT IO N S PK30 0 A SSEMBLY INS TRU CTIONS (www. pkg r i l ls. co m/a ssembl y vi d eos )
- Page 2 GET T IN G R E A DY Carefully unpack all components. Tools needed: phillips #3 screwdriver, 4 mm hex wrench, 5 mm hex wrench www.pkgrills.com/assemblyvideos 4mm Hex Wrench 5mm Hex Wrench Philips Screwdriver ASS E MB L E C A R T STEP 1.
- Page 3 (A) Top Notches Birds eye view of tubes. FIG 1 IMPORTANT: CHECK TUBE ORIENTATION - The notches (A) on the top of the tube must all face inward - in the direction of the long side of the cart. See FIG. 1 for correct orientation.
- Page 4 Screws STEP 4. Affix VERTICAL TUBES to LOWER CART TUBE ASSEMBLY using provided hex screws and 4mm hex wrench. Do not fully tighten. STEP 5. Place UPPER CART TUBE ASSEMBLY on top of the four VERTICAL TUBES as shown. The SHELF should be oriented on the side opposite the wheels.
- Page 5 Screws STEP 6. Affix VERTICAL TUBES to UPPER CART TUBE ASSEMBLY using provided hex screws and 4mm hex wrench. Do not fully tighten. STEP 7. Put LOWER SHELF in place. The assembled cart should look as shown here. If so, fully tighten the eight (8) hex screws into the cart lugs. PK30 0 A SSEMBLY INS TRU CTIONS (www.
- Page 6 STEP 8. Affix SPEED RACKS to vertical bars on stand using 5mm hex wrench (8X: 5 mm X 45 mm long stainless steel machine screw, 8X: Stainless Steel Cap nuts) STEP 9. Affix LEFT SHELF to stand using 5mm hex wrench (2X: C-Clamps, 4X: 5mm X 16 mm long stainless steel countersunk machine screws) ( www.pkg r ills.c om /a ssem b l y v id eos ) P K 3 00 A SSE M BLY I NS TRUC TI ONS...
- Page 7 B EL LY BA R STEP 1. Affix 2X BELLY BAR MOUNTS to vertical bars on stand using 5mm hex wrench (4X: 5 mm X 55 mm long stainless steel machine screw) PK30 0 A SSEMBLY INS TRU CTIONS (www. pkg r i l ls. co m/a ssembl y vi d eos )
- Page 8 STEP 2. Affix BELLY BAR WIRE to BELLY BAR SHELF using STEP 3. Affix BELLY BAR SHELF to BELLY BAR MOUNTS 5mm hex wrench using 5mm hex wrench (8X: 5mm X 18 mm long stainless steel countersunk (4X : 5mm X 18 mm long stainless steel countersunk machine screws) machine screws) ( www.pkg r ills.c om /a ssem b l y v id eos ) P K 3 00 A SSE M BLY I NS TRUC TI ONS...
- Page 9 ASS E MB L E LOWE R C A P SULE M6 Screw STEP 1a. Attach SHELF LOCKS to LOWER CAPSULE STEP 1b. Attach VENT HANDLES to LOWER RADIAL oriented as shown using provided M6 screws and lock VENTS using provided M6 screws. Handles are identical, washers.
- Page 10 STEP 4. Put the two VENT COVERS in place inside the STEP 5. Install the CHARCOAL GRATE and upper COOKING LOWER CAPSULE as shown. SURFACE as shown. STEP 6. Place REMOVABLE COOKING SURFACE DOOR on right side. Note that the REMOVABLE COOKING SURFACE DOOR is designed to easily hinge open and closed or to be completely removed for easy access to coals in indirect cooking scenarios.
- Page 11 ASS E MB L E U P P E R C A P SULE STEP 1. Place the UPPER CAPSULE on the LOWER CAPSULE with hinge oriented as shown. STEP 2. Open the UPPER CAPSULE into the open position and affix the handle using a no.
- Page 12 www.pkgrills.com/assemblyvideos STEP 3. Take a picture. (It will never be this pretty again.) Fire it up. ( www.pkg r ills.c om /a ssem b l y v id eos ) P K 3 00 A SSE M BLY I NS TRUC TI ONS...
Need help?
Do you have a question about the Original PK300AF and is the answer not in the manual?
Questions and answers