Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mackie THRASH212 GO
Summary of Contents for Mackie THRASH212 GO
- Page 10 12" Battery-Powered Loudspeaker O W N E R ’ S M A N U A L...
-
Page 11: Important Safety Instructions
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service. Thrash212 GO 12" Battery-Powered Loudspeaker... -
Page 12: Table Of Contents
Bluetooth® streaming 2. Power Switch ..........9 3. XLR and 1/4” Combo Input Jacks ..9 Link via Bluetooth to a second Thrash212 GO 4. Gain Knobs [Ch. 1 and 2] ..... 10 for stereo music playback 5. Thru Jack ..........10 Built-Like-A-Tank™... -
Page 13: Introduction / Getting Started
Introduction Getting Started Thrash212 GO is a full-size, battery-powered loudspeaker The following steps will help you set up the Thrash212 GO that delivers professional sound, anywhere. quickly. Forget long power cable runs—the swappable, rechargeable 1. Make all initial connections with the power switches battery lasts up to 10 hours, so you can take your music OFF on all equipment. -
Page 14: Hookup Diagrams
2 input. The gain knob should be set to line. Another Thrash212 GO loudspeaker will be used for the main PA. Simply connect a cable from the Thrash212 GO monitor’s THRU jack to the Thrash212 GO PA’s channel 1 input. - Page 15 Another Thrash212 GO loudspeaker will be used for extra “punch”. Simply connect a cable from the first Thrash212 GO’s THRU jack to the other Thrash212 GO’s channel 1 input. The gain knob of this input should be set to line.
- Page 16 In this example, a ProFX10v3 mixer is connected directly to two Thrash212 GO loudspeakers. It is the perfect setup for a small club. Simply connect the L/R outputs of the ProFX10v3 mixer to the channel 1 input of each Thrash212 GO loudspeaker.
- Page 17 NOTE: Make sure to set the gain knob(s) correctly. In the top diagram, all channel 1 inputs are set to “LINE” and in the bottom diagram, input channel 1 of the first Thrash212 GO is set to “MIC”, but the remaining ones should be set to “LINE”.
-
Page 18: Thrash212 Go: Rear Panel Features
1/4" mono (TS) phone plug, wired as follows: Press the top side of this rocker switch inwards to turn on the Thrash212 GO. Press the bottom side of this 1/4" TS Unbalanced Mono Wiring: rocker switch inwards to turn off the Thrash212 GO. -
Page 19: Gain Knobs [Ch. 1 And 2]
It ranges from off (– ) to MAX (maximum gain). distortion could occur, and not too low, where • Thrash212 GO is designed to operate with a +4 dBu the quieter, exquisitely-delicate passages might average line signal when the main knob and the line be lost in background noise. -
Page 20: Speaker Link
To unlink: The Bluetooth connection will disconnect In order to unlink the two Thrash212 GO if it’s out of range or if Thrash212 GO is powered loudspeakers, press and hold the ‘Link’ momentary off. Previously paired and connected devices switch / LED down on one of the Thrash212 GO will automatically reconnect and the pair button loudspeakers until the blue LED turns off. -
Page 21: Final Thoughts
BATTERY / COVER REMOVAL INSTRUCTIONS: on. Then, holding both the pair and link buttons Unplug Thrash212 GO and set it down with the grille (while either is engaged) clears all paired devices side facing down on a soft, flat surface. -
Page 22: Protection Circuitry
Continuing on, the driver has its own compression of Thrash212 GO and press down. Again, this is circuit which helps protect it from damaging transient an easy process; no force is necessary. -
Page 23: Ac Power
– while highly unlikely – death. can supply enough amperage for all the components Make sure that the Thrash212 GO is installed in a stable connected to it. and secure way in order to avoid any conditions that may be dangerous for persons or structures. -
Page 24: Room Acoustics
Room Acoustics Thrash212 GO is designed to sound fantastic in nearly every application. But, room acoustics play a crucial role in the overall performance of a sound system. However, the wide high-frequency dispersion of Thrash212 GO helps to minimize the problems that typically arise. -
Page 25: Appendix A: Service Information
Troubleshooting • Is there a light dimmer or other SCR-based device on the same AC circuit as the Thrash212 GO? Use an No power AC line filter or plug the loudspeaker into a different • Our favorite question: Is it plugged in and/or is AC circuit. -
Page 26: Appendix B: Technical Information
7.6 k points and is not suitable for rigging. Never attempt to suspend 1/4" TRS / XLR 1 M balanced / 7.6 k a Thrash212 GO by its handle. Output Type Male XLR Balanced [Thru] See pages 14–15 for more information. -
Page 27: Thrash212 Go Block Diagram
Thrash212 GO Block Diagram Thrash212 GO 12" Battery-Powered Loudspeaker... -
Page 28: Thrash212 Go Dimensions
Thrash212 GO Dimensions 14.8” / 375 mm 12.3” / 313 mm WEIGHT 35.9 lb/16.2 kg Owner’s Manual... -
Page 29: Limited Warranty
For full terms and conditions, as well as the specific duration of the Warranty for this product, please visit www.mackie.com. The Product Warranty, together with your invoice or receipt, and the terms and conditions located at www.mackie.com constitutes the entire agreement, and supersedes any and all prior agreements between LOUD and Customer related to the subject matter hereof. - Page 30 19820 North Creek Parkway #201 Bothell, WA 98011 • USA Phone: 425.487.4333 Toll-free: 800.898.3211 Fax: 425.487.4337 www.mackie.com...
- Page 31 10 hours, so you can take your music to new places. With onboard Bluetooth® connectivity, you can link to a second Thrash212 GO in stereo for a completely wireless music streaming system. Thrash212 GO offers Mackie-level performance thanks...
- Page 32 THRASH212 GO SPECIFICATIONS Acoustic Performance Line Input Power Frequency Response (–10 dB) 52 Hz – 20 kHz Detachable line cord 100–120V~, 50–60Hz, Frequency Response (–3 dB) 65 Hz – 20 kHz 75W, input current 2A 220–240V~, 50–60Hz, Horizontal Coverage 90°...
- Page 33 Floor mount or pole mount via the built-in socket on the bottom of the cabinet [Be sure the pole is capable of supporting the weight of the Thrash212 GO]. They are NOT designed to be suspended. The cabinet has no rigging points and is not suitable for rigging.
- Page 34 THRASH212 GO BLOCK DIAGRAM 4/5 PAGES...
- Page 35 Therefore, we reserve the right to change these specifications at any time without notice. www.mackie.com “Mackie” and the “Running Man” figure are registered trademarks 19820 North Creek Parkway #201 of LOUD Audio, LLC. All other brands mentioned are trademarks...
Need help?
Do you have a question about the THRASH212 GO and is the answer not in the manual?
Questions and answers