Do you have a question about the FLEX LS and is the answer not in the manual?
Questions and answers
Shelah Shelton
May 15, 2025
Bed will not move when using the remote. New batteries in remote. Bed does not respond to commands.
1 comments:
Mr. Anderson
May 22, 2025
If the Bedgear LS bed does not respond to the remote commands despite having new batteries, follow these steps to re-pair the remote:
1. Remove the 9V backup batteries from the power supply. 2. Press and hold the head and foot buttons on the remote simultaneously until the blue backlights turn off. 3. Plug the power cord back into the power source. 4. Wait for an activation sound within 2 seconds, indicating the remote is paired with the adjustable base.
NOTE: BEDGEAR DISCLAIMS ANY LIABILITY FOR DAMAGES OR INJURIES base. If the plug does not fit your outlet, contact a qualified Electrician to install a WHICH MAY OCCUR DUE TO FAILURE TO PROPERLY FOLLOW ASSEMBLY suitable outlet.
Page 3
Open the box lid. Before discarding the packing materials, ensure that all the parts are accounted for. Accessories Box Mattress Retainer Bar Flat Mattress Retainer Bar (Exclusively for BEDGEAR Mattresses) A R D ×1 D B O ×1(2 for K/CK) ×1...
Page 4
Remove the bed from the box with a flipping Install 4 legs; make sure the motion; let the bed stand on the 4 legs. legs are tight. A R D D B O A R D H E A D B O H E A Install the remaining 2 legs on the foot end of the bed;...
(Exclusively for BEDGEAR Mattresses) Make the bed completely flat. Insert the flat mattress retainer bar into the A R D securing strap at the bottom of the BEDGEAR D B O mattress and then snap it into the mattress H E A retainer mounts.
Page 6
Alternatively, install the mattress retainer bar Insert the flat mattress retainer bar into the securing strap at the bottom of one side after another for non-BEDGEAR mattresses. the BEDGEAR mattress, and then snap it into the mattress retainer mounts. - 6 -...
Insert the batteries into Uncoil the AC power cord, connect the DC power cord to the power supply the remote control. and then connect the power supply to the AC power source. AC Power Source A R D HEAD FOOT D B O STOP H E A...
Page 8
Wireless Syncing Instruction Remote Control Instructions STEP 1:Make sure both remotes are individualy paired to the foundation. If the remote is not paired with the Press HEAD FOOT foundation, follow the pairing instructions. and hold Flat Position STEP 2:Make sure both foundations are at home (flat position).
Page 9
Spacing Connector for TXL/T/CKS (Optional) Pairing Remote Install two spacing connectors to ensure the gap between the two The original remote that comes in the box is already adjustable bases is consistent. paired to the foundation. No further action is required. In the event when the remote is not paired with the HEAD FOOT...
Slat Pack Installation Guide (Optional) Headboard Bracket Installation Guide (Optional) Headboard brackets are optional and not included. A 1/2” (13 mm) SLAT/ PLATFORM Leg Configuration Table LEGS socket and 1/2” (13 mm) wrench are required to complete the installation. (2) T-Brackets (8) M8*16 (4) Nuts (4) Washers...
Page 11
DISCONNECT Tap the Refresh Button to refresh BEDGEAR Mobile APP is a mobile application to control the BEDGEAR Adjustable Base with the BEDGEAR Products List RENAME mobile devices. The application is available for both iOS and Android based smart devices.
Need help?
Do you have a question about the FLEX LS and is the answer not in the manual?
Questions and answers
Bed will not move when using the remote. New batteries in remote. Bed does not respond to commands.
If the Bedgear LS bed does not respond to the remote commands despite having new batteries, follow these steps to re-pair the remote:
1. Remove the 9V backup batteries from the power supply.
2. Press and hold the head and foot buttons on the remote simultaneously until the blue backlights turn off.
3. Plug the power cord back into the power source.
4. Wait for an activation sound within 2 seconds, indicating the remote is paired with the adjustable base.
This answer is automatically generated