Bedgear FLEX SH Owner's Manual
  1. Manuals
  2. Brands
  3. Bedgear Manuals
  4. Indoor Furnishing
  5. FLEX SH
  6. Owner's manual

Bedgear FLEX SH Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

FLEX SH™ OWNER'S MANUAL
FLEX SH™ ADJUSTABLE BASE
DSF14W3MSA Rev 1.0 06/2023
- 1 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FLEX SH and is the answer not in the manual?

Questions and answers

Related Manuals for Bedgear FLEX SH

Summary of Contents for Bedgear FLEX SH

  • Page 1 FLEX SH™ OWNER’S MANUAL FLEX SH™ ADJUSTABLE BASE DSF14W3MSA Rev 1.0 06/2023 - 1 -...

  • Page 2: Safety & Warranty Warnings

    NOTE: BEDGEAR DISCLAIMS ANY LIABILITY FOR DAMAGES OR INJURIES base. If the plug does not fit your outlet, contact a qualified Electrician to install a WHICH MAY OCCUR DUE TO FAILURE TO PROPERLY FOLLOW ASSEMBLY suitable outlet.

  • Page 3: Accessories Box

    Open the box lid. discarding the packing materials, ensure that all the parts are accounted for. Mattress Retainer Bar Accessories Box Flat Mattress Retainer Bar (Exclusively for BEDGEAR Mattresses) A R D D B O H E A ×1(2 for K/CK) ×1(2 for K/CK)
  • Page 4 Remove the red plastic safety lock before unfolding your power foundation. Remove the red plastic Turn the locking pin 90° in Remove the folding locking safety clip. counter clockwise direction. pin by pulling upwards. Red Plastic Safety Clip Locking Pin Locking Pin Install 4 legs, make sure the Remove the bed from the box...
  • Page 5 Install the remaining 2 legs on the foot end of the bed, make sure the legs are tight. Motion sensor installation Uncoil the two DC power cords (connected to the control boxes) Motion Mounting and put them to the side of the bed. A R D Sensor Bracket...
  • Page 6 Make the bed completely flat. (Exclusively for BEDGEAR Mattresses) Insert the flat mattress retainer bar into the A R D securing strap at the bottom of the BEDGEAR D B O mattress and then snap it into the mattress H E A retainer mounts.
  • Page 7 Setup the power foundation with the bed frame and slat base. Take the bed out of the box, put it on the slat base, do not Turn over the bed. Uncoil the DC power cords. install any legs. A R D A R D D B O motion sensor...
  • Page 8 Make the bed completely flat with a flipping motion. Insert the flat mattress retainer bar into the securing strap at the bottom of the BEDGEAR Power Source mattress and then snap it into the mattress retainer mounts.

  • Page 9: Control Box

    Electronics Quick Reference Guide Remote Control Remote Control Foot Motor Head Massage Head Massage Lumbar Motor Lumbar Motor Motor Motor Foot Massage Foot Massage Motor Motor Head Motor Head Motor Audio Charger Charger System HD Motor FT Motor Neck Motor LB Motor LED(5V) USB(29V) HD Motor...
  • Page 10 Remote Control Instructions SETTING PROGRAMMABLE POSITION SELECT BUTTON Press these two button to select One-touch programmable positions. Head/Foot/Lumbar zone. ADJUST UNDER BED LIGHTING This button lifts the Head/Foot/ Under bed LED lighting on/off. Lumbar section of the foundation. This button lowers the Head/Foot/ Lumbar section of the foundation.

  • Page 11: Battery Level

    Foot Sync Instruction Pairing Remote The original remotes that came in the box are already paired to the foundations. ATTN: THE TWO REMOTES CANNOT BE USED AT THE SAME TIME No further action is required. In the event when the remotes are not paired with AFTER BEING SUCCESSFULLY SYNCHRONIZED.
  • Page 12 Massage off button the APP and does not require additional settings. * Remote interface varies in between different BEDGEAR Adjustable Base models. If you wish to disconnect from the current paired Adjustable Base, Enter the Settings Page and tap the Disconnect button.

  • Page 13: Headboard Bracket Installation Guide (Optional)

    Legs Installation Guide Headboard Bracket Installation Guide (Optional) Headboard brackets are optional and not included. A 1/2” (13 mm) Leg Configuration Table socket and 1/2” (13 mm) wrench are required to complete the installation. (2) T-Brackets (8) M8*16 (4) Nuts (4) Washers (2) Headboard Brackets Configuration...

  • Page 14: Audio System

    Audio System Pairing Instruction Frequently Asked Qustions 1. Once power is supplied, the audio kit begins to search pairing device Description automatically. It keeps searching until it pairs with other device successfully. Possible cause, correction & maintenance of problem It could only pair with one device at a time. If you want to pair with a different device, disconnect the paired device, before connect with the new device.

Table of Contents