Table of Contents
Advertisement
Quick Links
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Advertisement
Table of Contents
Related Manuals for Biostar BIH60-IHP
Summary of Contents for Biostar BIH60-IHP
-
Page 1: Fcc Warning
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 2: Table Of Contents
BIH60-IHP User’s Manual Table Of Contents FCC Warning ����������������������������������������������������������������������������������������������������������� 1 Chapter 1: Introduction ������������������������������������������������������������������������������������������� 3 1.1 Before You Start .............................3 1.2 Specifications ............................4 1.3 Rear Panel Connectors ...........................6 1.4 Motherboard Layout ..........................7 Chapter 2: Hardware installation ����������������������������������������������������������������������������� 9 2.1 Install Central Processing Unit (CPU) .....................9 2.2 Install a Heatsink ..........................11... -
Page 3: Chapter 1: Introduction
BIH60-IHP User’s Manual Chapter 1: Introduction 1�1 Before You Start Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: • Prepare a dry and stable working environment with sufficient lighting. -
Page 4: Specifications
BIH60-IHP User’s Manual 1�2 Specifications Dimensions 170 x 170 Processor Intel® Alder lake s for LGA1700 Socket CPU (Max TDP at 65W) Core Logic (PCH) Intel® H610 LAN controller: I225V, I219-V*1 DDI to VGA: RTD2166 Chipsets Super IO : Fintek 81966D-I... - Page 5 BIH60-IHP User’s Manual Indicator 1x Green LED for 5V standby power indicator Hardware monitor CPU/System temperature, Voltage monitoring for VCC, 3.3, 5, 12V... Smart FAN 1 x 4pin CPU FAN & 1 x 3pin SYSTEM FAN, (CPU fan x1.system fanx1).
-
Page 6: Rear Panel Connectors
BIH60-IHP User’s Manual 1�3 Rear Panel Connectors CN1/ CN2: COM Port (DB9) Mode RS-422 RS-485 RS-232 Pin Define (1T/1R Full (1T/1R TX Enable (3T/5R) Duplex) Low Active) COM1C_DCD TX(B) (R(B) / T(B)) COM1C_RXD TX(A) (R(A) / T(A)) COM1C_TXD RX(A) COM1C_DTR... -
Page 7: Motherboard Layout
BIH60-IHP User’s Manual 1�4 Motherboard Layout CN52 » » represents the 1st pin. Chapter 1: Introduction | 7... - Page 8 BIH60-IHP User’s Manual Back View 8 | Chapter 1: Introduction...
-
Page 9: Chapter 2: Hardware Installation
BIH60-IHP User’s Manual Chapter 2: Hardware installation 2�1 Install Central Processing Unit (CPU) Step 1: Locate the CPU socket on the motherboard Note » » Remove pin cap before installation, and make good preservation for future use. When the CPU is removed, cover the pin cap on the empty socket to ensure pin legs won’t be damaged. » » The motherboard might equip with two different types of pin cap. Please refer below instruction to remove the pin cap. Step 2: Open ILM Lever and then load plate using finger tab... - Page 10 BIH60-IHP User’s Manual Step 4: Close the load plate Step 5: Remove and save cover Step 6: Close ILM Lever and latch Note » » Ensure that you install the correct CPU designed for LGA1700 socket. » » The CPU fits only in one correct orientation. Do not force the CPU into the socket to prevent damaging the CPU. 10 | Chapter 2: Hardware installation...
-
Page 11: Install A Heatsink
BIH60-IHP User’s Manual 2�2 Install a Heatsink Step 1: Place the CPU fan assembly on top of the installed CPU and make sure that the four fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest to the CPU fan connector. -
Page 12: Fan Headers
BIH60-IHP User’s Manual 2�3 Fan Headers These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. -
Page 13: Installing Memory Module
BIH60-IHP User’s Manual 2�4 Installing Memory Module DIMM1/ DIMM2: DDR4 Memory Module Slot (260pins SO-DIMM) Note » » If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again. Insert memory module into SO-DIMM socket at backside of motherboard. 1. Hold the SO-DIMM with its notch aligned with the memory socket of the board and insert it at a 30-degree angle into the socket. -
Page 14: Expansion Slots
BIH60-IHP User’s Manual 2�5 Expansion Slots CN20: PCI-Express Gen3 x16 Slots (x16 mode) • PCI-Express 3.0 compliant. • The maximum bandwidth of the PCIe slot is 32GB/s. CN21: Mini PCI-Express Connector • The half-size mPCIe socket supports mini PCIe module. - Page 15 BIH60-IHP User’s Manual SCN1: M�2 (B Key) Socket • Supports M.2 socket 2242/ 2280/ 3042/ 3052 type module. • Supports PCIEx2, PCIe + SATA3.0, PCIe + USB3.1 interfaces by BOM option. (Default is PCIe + USB3.0.) Installing WiFi Module 1. Insert WiFi module into mini PCIe slot (CN21) 2.
-
Page 16: Jumper & Switch Setting
BIH60-IHP User’s Manual 2�6 Jumper & Switch Setting Jumper Setting The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened... - Page 17 BIH60-IHP User’s Manual JP1: COM VDD Pin 3-5 Close: DCD signal (Default) Assignment Pin 4-6 Close: RI signal DCD_H RI_H Pin 1-3 Close: 5V Pin 2-4 Close: 12V Chapter 2: Hardware installation | 17...
-
Page 18: Headers & Connectors
BIH60-IHP User’s Manual 2�7 Headers & Connectors CN30: ATX Power Source Connector For better compatibility, we recommend to use a standard ATX 24-pin power supply for this connector. Make sure to find the correct orientation before plugging the connector. Assignment Assignment +3.3V... - Page 19 BIH60-IHP User’s Manual CN80: Front Panel Pin Header This connector includes Power-on, Reset, HDD LED and Power LED connections. It allows user to connect the PC case’s front panel switch functions. Assignment Assignment Buzzer Buzzer EXT SPK- EXT SPK+ PWRLED-...
- Page 20 BIH60-IHP User’s Manual CN3/ CN4: COM Header Assignment Assignment CN62: USB Header These connectors support the thin Serial ATA cable for primary internal storage devices. Pin Assignment CN50: EDP Connector This connector supports 18/24 bit single-channel panels. Assignment Assignment EMB_HPD...
- Page 21 BIH60-IHP User’s Manual CN81: SPI Header Pin Assignment MISO MOSI CN26: Digital I/O Connector Pin Assignment CN29: LVDS Connector Assignment Assignment VCCM VCCM VCCM VCCM VCCM VCCM LVDS_EDID_SCL LVDS_EDID_SDA LVDSB_DATA0_N LVDSB_DATA3_N LVDSB_DATA0_P LVDSB_DATA3_P LVDSB_DATA1_N LVDSB_CLK_N LVDSB_DATA1_P LVDSB_CLK_P LVDSB_DATA2_N LVDSA_DATA0_N LVDSB_DATA2_P...
- Page 22 BIH60-IHP User’s Manual CN55: LVDS BKLT CONTROL Pin Assignment VCC 12V0 VCC 12V0 VCC 5V0 BKLTEN_LVDS LVDSPWMOUT SCN2: SIM Slot Pin Assignment UIM_PWR UIM_Reset UIM_CLK Data 22 | Chapter 2: Hardware installation...
Need help?
Do you have a question about the BIH60-IHP and is the answer not in the manual?
Questions and answers