Related Manuals for SNBC BTP-L580IIP
Summary of Contents for SNBC BTP-L580IIP
- Page 1 USER’S MANUAL Label Printer BTP-L580IIP Shandong New Beiyang Information Technology Co., Ltd...
- Page 2 INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right to improve products as new technology, components, software, and hardware become available. If users need further data about these products, please feel free to contact SNBC or your local dealer.
- Page 3 BTP-L580IIP User’s Manual Safety instructions Before installing and using the printer, please read the following items carefully: Safety warning 1． Warning Do not touch the cutter or tear of the printer. Warning The print head is a thermal element and it is at a high temperature during printing or just after operation, therefore do not touch it or its peripherals for reasons of safety.
-
Page 4: Table Of Contents
BTP-L580IIP User’s Manual Contents 1 Overview ..........................1 1.1 Introduction........................1 1.2 Main features ........................1 2 Specifications........................2 2.1 Technical specifications....................2 2.2 Paper specifications ......................3 2.2.1 Parameters of label paper ..................3 2.2.2 Paramters of thermal continuous paper ..............3 2.2.3 Parameters of marked paper ...................4 2.3 Print and tear-off position ....................5... - Page 5 BTP-L580IIP User’s Manual 4.10 Guide for hexadecimal dumping mode ................. 13 4.10.1 Hexadecimal dumping function................13 4.10.2 Running hexadecimal dumping ................13 5 Routine maintenance ......................14 5.1 Clean print head and platen roller................14 5.2 Clean sensors ......................14 5.3 Clear paper jam ......................
-
Page 6: Overview
1 Overview 1.1 Introduction BTP-L580IIP is a high performance thermal label printer, which can be widely used for real-time label printing applications, such as retailing, storage, logistics, medicine, etc. BTP-L580IIP can be connected with other devices via parallel, serial, USB, Ethernet or WLAN interface and can provide drivers for operating systems such as WINDOWS 2000/ XP/Server2003/VISTA/ Server2008/WIN7, Linux, MAC and label software. -
Page 7: Specifications
BTP-L580IIP User’s Manual 2 Specifications 2.1 Technical specifications Item Parameter Print method Direct thermal line Print resolution 203DPI Print speed Label paper: 150mm/s continuous paper: 230mm/s Print width Max. 80mm Thermal label paper roll, thermal continuous paper roll, thermal Paper type... -
Page 8: Paper Specifications
BTP-L580IIP User’s Manual 2.2 Paper specifications 2.2.1 Parameters of label paper Paper type: thermal label paper Paper supply mode: paper roll Thermal layer: outward Paper reflectivity: Label: reflectivity＜18% base paper: reflectivity＞47% Paper width: 54.5±0.5 mm~82.5±0.5 mm Backing paper thickness: 0.041mm-0.071mm Thermal paper (label) thickness: 0.070mm-0.092mm... -
Page 9: Parameters Of Marked Paper
BTP-L580IIP User’s Manual 2.2.3 Parameters of marked paper BTP-L580IIP can support marked paper printing and set the cutting and initial printing position accurately. Marked paper not only should meet the parameters of thermal paper roll, but also should meet the following requirements: L1 mark height: 3mm≤L1≤13mm... -
Page 10: Print And Tear-Off Position
BTP-L580IIP User’s Manual 2.3 Print and tear-off position 2.3.1 Print position L1 paper cabinet width: 83.5+0/-0.5mm L2 effective print width: 80mm L3 distance from print head to left edge of paper cabinet (fixed width): 1.75±1mm L4 distance from print head to right edge of paper cabinet (fixed width): 1.75±1mm L5 left margin: The default value is 5mm. -
Page 11: Appearance And Modules
BTP-L580IIP User’s Manual 3 Appearance and modules 3.1 Appearance and modules 1—paper guide 2—paper near end sensor lever 3—mark sensor 4—platen roller 5—peel-off bar 6—peel-off platen roller 7—peel-off holder 8—peel-off lever 9—tear-off bar 10—print head 11—roller 12—cover open lever 13—top cover 14—middle cover... -
Page 12: Led & Buzzer
BTP-L580IIP User’s Manual setting (configuring) by Feed button) if pressing down the FEED button for a long time. Refer to Appendix Button Configuration Menu for the detailed function and operation method of button configuration mode; 2) If selecting “Calibration”, the printer will do paper calibration;... - Page 13 BTP-L580IIP User’s Manual Caution: The temperature of the print head is detected by a thermal resistor. If the print head is overheating, the protective circuit will shut off the power and force the printer to stop printing; the temperature of print head when printing is stopped is 65 ℃...
-
Page 14: Printer Installation
4.1 Unpacking Check if all the articles listed in the packing list are here and in good condition. If any problem, please contact SNBC or the dealer. 4.2 Printer installation Printer should be installed on a flat and stable place; horizontal installation is recommended and the inclination angle should not exceed ±10°... -
Page 15: Connect Interface Cable
BTP-L580IIP User’s Manual When the power is burned out or cannot be used for other reasons, replace it according to the following steps: 1) Press the power cover board and take it off in the direction indicated by the arrow;... -
Page 16: Install/Replace Paper Roll
BTP-L580IIP User’s Manual 4.7.2 Install/replace paper roll Turn off the printer; Press the cover open lever to open the top cover; Place a paper roll into the paper cabinet; Pull the paper head out, close top cover and tear off the surplus portion of the paper;... -
Page 17: Power-On And Self-Test
BTP-L580IIP User’s Manual Level Level Level Leve Level Level Level Core diameter A (mm) A: core ID B: core OD C: paper roll OD Caution: The factory default position of paper near end sensor lever is at level 1. The requirement for the core with big diameter can be met by adjusting paper near end sensor lever;... -
Page 18: Guide For Hexadecimal Dumping Mode
BTP-L580IIP User’s Manual 4.10 Guide for hexadecimal dumping mode 4.10.1 Hexadecimal dumping function This function prints the data transmitted from the host computer in hexadecimal numbers and in their corresponding characters. Print sample in Hexadecimal Dump mode: 4.10.2 Running hexadecimal dumping 1) Start hexadecimal dumping by executing either of the following: a. -
Page 19: Routine Maintenance
BTP-L580IIP User’s Manual 5 Routine maintenance Caution: Before starting routine maintenance, ensure that the printer power is turned off; Do not use solvents like gasoline or acetone; When cleaning sensors, the printer should not be powered on until the pure alcohol has completely evaporated. - Page 20 BTP-L580IIP User’s Manual rename it to BY_EEP.eep; Insert the U-Disk into the USB interface of printer; After opening the top cover, press the FEED button while powering on the printer; Release the button immediately when the error LED is on. The time of pressing the button after powering on the printer should be controlled within two seconds;...
-
Page 21: Interface Signal
BTP-L580IIP User’s Manual 6 Interface signal 6.1 Parallel interface Parallel interface can work in IEEE 1284 compatible mode or nibble mode. The interface is 36-pin socket. The Interface is defined as below: Signal Signal definition source nStrobe Data 0 (Least Significant Bit) -
Page 22: Serial Interface
BTP-L580IIP User’s Manual Not defined Not defined nSelectIn 6.2 Serial interface The serial interface of the printer is compatible with RS-232, and the interface socket is DB25 female. PIN No. Signal definition PIN1 Frame ground PIN2 PIN 3 PIN 4... -
Page 23: Wlan Interface
BTP-L580IIP User’s Manual Compatible with Ethernet II standard LED displays network connecting status and data transmission status Support 9100 port print Support status back Support parameter configuration Support firmware online update Support printer status query and interface module maintenance based on HTTP (only supported by JK-E02 interface, not supported by JK-E04 interface). -
Page 24: Power Interface Definition
BTP-L580IIP User’s Manual DHCP TFTP HTTP Wireless interface module uses wireless USB network card. For the main technical specifications, please contact your local dealer or SNBC. 6.6 Power interface definition Power interface signal definition Signal name Figure 6.6-1 Power socket 6.7 Signal definition of cash drawer interface... -
Page 25: Troubleshooting
BTP-L580IIP User’s Manual 7 Troubleshooting Refer to this chapter for solution when a problem occurs. If the problem still cannot be solved, please contact your local dealer or SNBC for assistance. 7.1 Printer doesn’t work Problem Possible causes Solution Printer is not connected with power Connect the printer with power supply. -
Page 26: Power Management
Related parameters of power management are as below: Maximum default delay time of entering sleep mode is less than 5 minutes; Since the maximum default delay time is less than 5 minutes, BTP-L580IIP does not open the interface of changing this time to user. -
Page 27: Appendix: Button Configuration Menu
BTP-L580IIP User’s Manual Appendix: Button configuration menu Refer to BTP-L580IIP Printer's Parameter Setting Menu by Feed Button. - 22 -...
Need help?
Do you have a question about the BTP-L580IIP and is the answer not in the manual?
Questions and answers