Advertisement
Quick Links
TJ06 ・ TJ15
Model
Installation Manual
❖Accessories of Installation
Description of goods
Bracket for machine
Slide plate
Electrical cable
Relay cable for Motor & Solenoid
Foot switch
Air hose
Air regulator
Bolts
①Fixtyre bolts for bracket
②Fixture bolts for machine
③Fixture bolts for slide plate
④Pass line adjusting
Fixture bolts for air regulator
Bonding
Mark tube, Terminal
Sticker
Noise filter
Fixing bolt, spring washer, washer
Air connector
❖Bolt-positionsfor the machine setting
CAUTION
❖Code
Feed Lengh ( L )
ENG
STOP
I - F
O_run
8-M8*15,Spring washer, Washer
4-M4, Spring washer, Washer
③
Please note whether T throttle nuts are inserted because of closing the
grooves by the bracket for feeder.
Feed Length ( R )
4. 4 . 4 . 4 . 4 . 4 .
Emergency stop switch ON
444444
Emergency stop switch OFF
Input stop signal during driving
1. 0 . 1 . 0 . 1 . 0 .
press
Input stop signal release
101010
Input stop signal
1. 1 . 1 . 1 . 1 . 1 .
Interfere releasing
661661
Input feed signal during feeding
662662
Input feed signal during releasing
663663
Input release signal during feeding
664664
Overrun
666666
TJ06 ・ TJ15
Exclusive type：2 sets
Exclusive plate：2 sets
Power, Signal, Emergency
1-6M
1
8*5：6M
Standard
4-M12*30
8-M10*25, Washer
2-M12*120
2-M6*12
Net 4ml
Assortment
Signal, Scale for pass line
4-M4*15+nut／4-M10
1-3/8B, 1-UT-8, 2-2/8B
②
①
Contents
1
DIMAC
Foot switch
Air regulator
Noise filter
④
Method of reset
After releasing the Emergency
stop switch, turn off the power
Turn on Reset switch after input
stop signal release
Turn on Reset switch
Automatic reset after clear
Turn on "Reset" switch
Turn on "Sync Feed" and "Sync
Release" after turn on "Reset"
switch
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dimac TJ06
Summary of Contents for Dimac TJ06
- Page 1 DIMAC TJ06 ・ TJ15 Model Installation Manual ❖Accessories of Installation Description of goods TJ06 ・ TJ15 Foot switch Bracket for machine Exclusive type：2 sets Slide plate Exclusive plate：2 sets Electrical cable Power, Signal, Emergency Relay cable for Motor & Solenoid...
-
Page 2: Slide Plate
103 ～145 83～125 Bolster ❖Slide plate TJ06・TJ15 : The standard product is equipped with a slide plate. By using the slide plate, you will be able to slide the machine mounted to left and right. TJ06・TJ15 Plate fixing bolt：3-M8*15 Slide plate... - Page 3 ❖Wiring There are three of circuit relay which are listed A,B,C below and an electrical power. Circuit relay A Circuit relay B Circuit relay C 1A at AC 250V or less 1A at AC 250V or less 1A at DC 30V or less 1A at DC 30V or less 5V GND 24V GND...
- Page 4 Need to fix all connecting cables by using some prepared clampers and Nylon DANGER band. ❖Relay cable connecting TJ06, TJ15 The relay-cables are connected outside of the feeder. Covered connectorparts ❖Air piping 2/8B...
- Page 5 ❖ Press synchronous operation Setting press cam signal for feed 0° Set the feed start position to feed signal OFF position. When you make the feed starts on 270° Set the ON angle of feed to 240°, and set the 90°...
- Page 6 ❖ Auto drive setting for Sheet Mode When input power, the feeder starts up in "Set" state The blinking display is a changeable item. Using ← → switch, you can change the position. Change the setting value with + / - switch.
Need help?
Do you have a question about the TJ06 and is the answer not in the manual?
Questions and answers