Page 1
S C R U BB E R D RY ER A U TO LAV EU SE Original Instructions CAUTION, Read instructions before using the machine Keep for future reference Notice originale MISE EN GARDE Lisez la notice avant d’utiliser la machine À conserver pour référence future nacecare.com...
Index PLEASE READ BEFORE COMMENCING Machine Overview .........Pages 2-3 OPERATION Control Panel Overview .........Page 4 After the removal of all the packaging, Machine Set up Guide .........Page 5 carefully open and check the contents Fitting the Brush / Pad .........Page 5 Fitting the Floor Tool .........Page 5 Owner Manual...
Control Panel Overview Battery Charge Level Display Water Flow Indicatorv Handle Position Lever In the event of a breakdown contact Start Switch your Numatic dealer or the Triggers Numatic Technical Help line +44 (0)1460 269268...
Machine Set-up Guide ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF BEFORE MAKING ANY ADJUSTMENTS Fitting the Brush/Pad Turn on Water 18” Brush or 16” Pad. Featuring the Nulock brush system. Slide the brush / pad under the brush deck. Fit the brush / pad onto the Nulock drive chuck, twist to lock the brush / pad in place.
Machine Set-up Guide Fitting the Hose Guide The vacuum hose has a U-bend clip which creates a U-bend in the hose preventing water Note: DO NOT push the vacuum hose the raised position. or hose pipe. (Fig.A & B). required. Follow chemical manufacturing guide lines. The clear dump hose at the rear of the machine can be used to see the level of the clean-water.
Machine Set-up Guide Handle Height Adjustment Using the handle position lever, lower the handle to a comfortable working position. IMPORTANT The machine is now ready to be moved to the cleaning site. Before performing the cleaning operation, place out appropriate warning signs and sweep or dust-mop the Open the battery door (A).
Machine Operation Raising/Lowering the Floor Tool ready to set the controls to suit the cleaning conditions. Before any settings can be applied, ensure the brush lower position. To tip the deck into the down position (Operating mode). Press in the brush deck locking pin (Fig.A) and rotate the brush deck (Fig.B &...
Page 9
Machine Operation settings pull either trigger and press the Start switch (A). The running state of the vacuum (D) and water (C) can be adjusted whilst the brushes are running. To cancel vac overrun press any switch (vac/water/handle/start) will stop operating. The errors are split into two groups, low and high priority.
Brush Pressure / Load Adjustment Pressure Weights a ‘Deck Pressure Weight’ allowing the operator to add or remove pressure on the brush or pad for optimum performance on Remove the Top (Waste Water) tank (1). Set in the lower tank are location pillars (2) to locate the Deck Pressure Weights (5).
Machine In Use ALWAYS ENSURE THAT THE FLOOR IS Machine In Use PRE-SWEPT AND RELEVANT SAFETY SIGNS ARE DISPLAYED. Overlap each scrubbing path by 4” to ensure an even clean. Do not operate the machine on inclines that exceed (2%), when full. Regular Maintenance ALWAYS ENSURE THAT THE MACHINE IS SWITCHED...
Page 12
Changing the Floor Tool Blades the holder. checked for wear and damage. The blade removal is easy. Simply start by removing the four carrier from the body. Peel away the blades from their locating lugs and examine or renew as required. Replacement is a reversal of the removal process.
Company Name & Address Model Voltage / Direct Current Rated Input Power WEEE Logo Ingress Protection Max Gradient Approval Mark Weight (ready to use) Machine yr/wk Serial Number Model Noise Rating Hand Arm Vibration TwinTec Keep the machine clean. Maintenance Check for any worn or damaged parts and replace immediately.
Page 14
READ MANUAL BEFORE USE COMPONENT INTERVAL INSPECT FOR Mains Lead DAILY Brushes DAILY Bristle damage, wear, drive collar wear Squeegee Blade BEFORE EACH USE Wear, cracks, splits Filters BEFORE EACH USE Clogging and debris retention Tanks AFTER EACH USE Rinse dirty water tank after use WARNING Read the instruction manual before using the appliance.
Schematic Diagram Spare Parts BRUSHES CHARGER AND BATTERY 606203 450mm Polyscrub Brush 913686 LITHIUM ION BATTERY 606204 450mm Nyloscrub Brush 910820 DUAL LITHIUM BATTERY CHARGER 606306 450mm Longlife Brush 912365 CHARGER CABLE (UK) 900525 400mm NuLoc2 Drive Board PROBLEM CAUSE SOLUTION Machine will not operate Low battery charge...
Page 16
Address: CBAK BATTERY HEADQUARTERS NUMATIC INTERNATIONAL LTD Shenzhen BAK ENERGY Co. LTD, 2603A BAK Tech Bldg, Chard, 9th Keyan Rd, Hi-tech Park, Somerset, Nanshan Dist, TA20 2GB, UK Shenzhen City, China Tel: 0086-755-83283710 0044-146-068600 0086-755-8328649 0044-146-068458 1. DEFECTIVE BATTERIES If a customer wishes to return a battery to a supplier, then collection of the battery must be arranged by the supplier; however, If on return to a supplier, OR at a customer base, a suspected defective battery shows any signs of impact damage, distortion, considered defective and the procedures described from item 9 below should be followed.
Page 17
Store batteries out of reach of children. Insert the battery in the appliance only when it is in use. Always remove the battery from the appliance for transport and when it is not in use. Storage temperature range: -10°C~55°C. Temperatures must not exceed 55°C. Relative humidity range: 45 to 80%.
Page 18
5. FIRE FIGHTING MEASURES are especially suitable). Respiratory Protection is not necessary under conditions of normal use. Ventilation: Not necessary under conditions of normal use. Protective Gloves: Not necessary under conditions of normal use. Not necessary under conditions of normal use. Personal Protection is recommended for venting batteries: Respiratory Protection, Protective Gloves, Protective Clothing and safety glass with side shields.
10. DISTRIBUTOR TAKE-BACK / DISPOSAL of batteries used in devices. To this end, batteries must be handed over for disposal to the collection systems established for this under national law. Disposal of batteries together with household waste is prohibited; batteries must be collected separately according to type.
Need help?
Do you have a question about the Numatic NX300 and is the answer not in the manual?
Questions and answers