1. Manuals
  2. Brands
  3. PLANEPRINT Manuals
  4. Aircrafts
  5. Halo
  6. Assembling manual

PLANEPRINT Halo Assembling Manual

Flying wing for slope and coast fl ying
Hide thumbs Also See for Halo:

Advertisement

Table of Contents

Flying wing for slope and coast fl ying
www.planeprint.com
the ONLY place where you can get
original Planeprint STL fi les legally!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Halo and is the answer not in the manual?

Questions and answers

Related Manuals for PLANEPRINT Halo

Summary of Contents for PLANEPRINT Halo

  • Page 1 Flying wing for slope and coast fl ying www.planeprint.com the ONLY place where you can get original Planeprint STL fi les legally!
  • Page 2 LW-PLA CARBON HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 3 • Fabric tape for the aileron hinges • some lead Tapping screws Ø2mm Tools • Cutter knife • Drill Ø1.5mm • small Phillips screwdriver • Metal saw • Side cutter Carbon tube • Needle nose pliers Carbon rod HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 4 This manual is constantly being improved and supplemented, we recommend downloading the latest version from our website before building. To print all PLANEPRINT models you need to set some basic profiles in Cura (If you use another slicer, please set the same parameters).

  • Page 5: Additional Settings

    ADDITIONAL SETTINGS • Wall Line Count/Perimeters: 1 • Infi ll Density/Fill Density: 6 % • Infi ll Pattern/Fill Pattern: Gyroid • set Support P1_Nose_halo.stl MATERIAL PLA, Weight: ~ 19 g ADDITIONAL SETTINGS None required HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 6 The information about the basic settings you can fi nd on our website at PRINT. Please note the additional settings for the individual parts! P1_Parts_halo.stl MATERIAL PLA, Weight: ~ 4 g ADDITIONAL SETTINGS None required HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 7 The information about the basic settings you can fi nd on our website at PRINT. Please note the additional settings for the individual parts! P4_Wing mount_halo.stl MATERIAL TPU A95, Weight: ~ 1 g ADDITIONAL SETTINGS • Infi ll Density: 100 % HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 8 LW PLA, Weight: ~ 7 g ADDITIONAL SETTINGS • Infi ll Density/Fill Density: 4 % P5_Aileron L 2_halo.stl and P5_Aileron R 2_halo.stl MATERIAL LW PLA, Weight: ~ 7 g ADDITIONAL SETTINGS • Infi ll Density/Fill Density: 4 % HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 9 LW PLA, Weight: ~ 4 g ADDITIONAL SETTINGS • Infi ll Density/Fill Density: 4 % P5_Rudder 1_halo.stl MATERIAL LW PLA, Weight: ~ 4 g ADDITIONAL SETTINGS • Infi ll Density/Fill Density: 4 % • set Brim HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 10 • Infi ll Density/Fill Density: 4 % • set Brim P5_Wing L 1_halo.stl and P5_Wing R 1_halo.stl MATERIAL LW PLA, Weight: ~ 33 g ADDITIONAL SETTINGS • Infi ll Density/Fill Density: 4 % HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 11 • Infi ll Density/Fill Density: 4 % P5_Wing L 3_halo.stl and P5_Wing R 3_halo.stl MATERIAL LW PLA, Weight: ~ 13 g ADDITIONAL SETTINGS • Infi ll Density/Fill Density: 4 % • set Brim HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...

  • Page 12: Fuselage Assembly

    Align the rudder exactly vertically and drill a P1_Nose_halo.stl 1.5 mm hole in the carbon tube and screw the rudder in place. You can also glue it into the fuselage without the screw. The nose is simply pushed on. HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...

  • Page 13: Wing Assembly

    Wing assembly P5_Aileron L 3_halo.stl P5_Wing L 3_halo.stl P1_Parts_halo.stl P5_Aileron L 2_halo.stl P5_Wing L 2_halo.stl P5_Aileron L 1_halo.stl P5_Wing L 1_halo.stl Carbon tube Ø5*125mm HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 14 The servo must not protrude over the wing! The servo must be as close as possible to the underside of the wing. Steel wire Ø0.8*66.4mm HALO HALO PRINTING & ASSEMBLING MANUAL PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
  • Page 15 Carbon tube Ø5*250mm P4_Wing mount_halo.stl To mount the wings, you can always leave the TPU mount fi xed on a wing. You can store spare screws here. HALO HALO PRINTING & ASSEMBLING MANUAL PRINTING & ASSEMBLING MANUAL © PLANEPRINT © PLANEPRINT...

  • Page 16: Center Of Gravity (Cg)

    If one wing is heavier, correct this with a small weight on the wingtip. Technical specifi cations WINGSPAN 1200 mm/47.2 inches 1200 mm/47.2 inches LENGTH 508 mm/20 inches 508 mm/20 inches FLIGHT WEIGHT 330 grams 330 grams WING LOAD 20 g/dm HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...

  • Page 17: Control Direction Test

    10 to 12 mm AILERON 10 to 12 mm 10 to 12 mm (for some remote EXPO ELEVATOR 70 % controls a minus has to be in front AILERON 20 % of the number) HALO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...

  • Page 18: Age Recommendation

    3D printing Always keep the transmitter switched on when the model will not be replaced by PLANEPRINT.com in any way. is switched on. When operating, always keep a safe distance from your Always remove the battery before disassembling the model.

Table of Contents