Related Manuals for PLANEPRINT RISE nano
Summary of Contents for PLANEPRINT RISE nano
- Page 1 You can fi nd the STL data NOTE: Slicing only at www.planeprint.com works with CURA!
- Page 2 LW-PLA CARBON STEEL RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 3 • Steel wire Ø0.8*1000mm, 1 piece • Carbon rod Ø4*1000mm, 1 piece • Rod connection small, 2 pieces • Neodym-Super-Magnet 5x5x5mm, 4 pieces Tools Cutter knife, Drill, small Philips screwdriver, Sandpaper, Metal saw, Needle nose pliers RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 4 3D printer is a very complex and extensive process. Therefore, we appeal to your fairness not to forward the STL data you have acquired to third parties. Thank you for your understanding and have fun with your PLANEPRINT MODEL! RISE NANO PRINTING &...
- Page 5 PROFILE P1_Fullbody PLA or Tough PLA The following parts must be sliced with the PROFILE P1_Fullbody. Please note the additional settings for the individual parts! P1_Motormount-XXX_Rn.stl MATERIAL PLA, Weight: ~ 1 g ADDITIONAL SETTINGS None required P1_Parts_Rn.stl MATERIAL PLA, Weight: ~ 3 g ADDITIONAL SETTINGS None required...
- Page 6 Please note the additional settings for the individual parts! P1_Protector_Rn.stl MATERIAL PLA, Weight: ~ 3 g ADDITIONAL SETTINGS None required P1_Spinner folding prop Xmm_Rn.stl MATERIAL PLA, Weight: ~ 1 g ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 7 The following parts must be sliced with the PROFILE P4_Flex. Please note the additional settings for the individual parts! P4_Hinges_Rn.stl MATERIAL TPU ~ A95, Weight: ~ 1 g ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 8 P5_Canopy_Rn.stl MATERIAL LW-PLA, ~ 2 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required P5_Elevator-L_Rn.stl and P5_Elevator-R_Rn.stl MATERIAL LW-PLA, ~ 2 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 9 P5_Fuselage 1_Rn.stl MATERIAL LW-PLA, ~ 6 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required P5_Fuselage 2_Rn.stl MATERIAL LW-PLA, ~ 7 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 10 LW-PLA, ~ 8 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS • Z Seam Position: back left P5_Wing 1-L_Rn.stl and P5_Wing 1-R_Rn.stl MATERIAL LW-PLA, ~ 20 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 11 P5_Wing 2-L_Rn.stl and P5_Wing 2-R_Rn.stl MATERIAL LW-PLA, ~ 19 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required P5_Wing 3-L_Rn.stl and P5_Wing 3-R_Rn.stl MATERIAL LW-PLA, ~ 8 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 12 Basic settings for LW-PLA: Please follow the instructions in our WINGTEST AND CALIBRATION TOOL on our website for correct adjustment! P5_Interconnects_Rn.stl MATERIAL LW-PLA, ~ 1 g* *Weighed (approximate guideline) ADDITIONAL SETTINGS None required RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
-
Page 13: Basic Information
After assembly, align the two parts exactly and wipe off the excess CA glue from the surface with a cloth. Now spray with activator spray along the gluing surface and carefully press the parts together. STEP 4 Clean the glued areas slightly with a sharp-bladed cutter. RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT... -
Page 14: Wings Assembly
Wings assembly Use the carbon rod for alignment but make sure that it is not glued! medium l. P5_Wing 3-L_Rn.stl P5_Interconnects_Rn.stl P5_Wing 2-L_Rn.stl P5_Wing 1-L_Rn.stl Carbon rod Ø4*580mm (Do not glue!) RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT... -
Page 15: Fuselage Assembly
Please be careful with the knife! Carbon rod Ø4*340mm Carbon rod Ø4*340mm P1_Protector_Rn.stl Use the carbon rods for alignment but make sure they are not glued along! P1_Protector_Rn.stl Carbon rod Ø4*80mm (Do not glue!) RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT... -
Page 16: Canopy Assembly
Canopy assembly Steel wire Ø0.8*60mm P5_Canopy_Rn.stl STEP 1 STEP 2 RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT... -
Page 17: Motor Mount
The prop must run absolutely accurate and balanced! Always keep it away from you (and other people) when starting the motor! P1_Motormount-31mm_Rn.stl P1_Spinner folding prop 6mm_Rn.stl RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT... -
Page 18: Tailplane Assembly
45° (about 1.5 mm gap in neutral position). Important: There must not be too much glue on the hinge and the elevator must move easily. P5_V-Tail_Rn.stl P5_Elevator-R_Rn.stl P1_Parts_Rn.stl P5_Elevator-L_Rn.stl P4_Hinges_Rn.stl RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT... - Page 19 V-tail on the rear carbon rod. When the V-tail rests on the table, it is automatically in the correct position relative to the fuselage. Then put thin CA glue in the gap of the carbon rod. RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 20 Servo mount The servos must sit as low as possible in the fuselage. There are two different servo holders in different heights, suitable for different servos. P1_Parts_Rn.stl RISE NANO RISE NANO PRINTING & ASSEMBLING MANUAL PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 21 One magnetic connection per side is suffi cient, if you want it to be particularly strong, you can place a second magnet in front of the carbon rod. Neodym Super Magnets 5x5x5 mm RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 22 RC components Battery Servos Controller RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
-
Page 23: Technical Specifications
The RISE nano has a wide speed range, which means you can fl y it very fast or relatively slow. In thermal conditions, the elevator should be trimmed up a few clicks to climb optimally in the updraft. You can also program two fl ight phases for this. - Page 24 Full Throttle ~ 10 % down ~ 10 % down Expo setting (for some remote ELEVATOR 20 % controls a minus has to be in front RUDDER 20 % of the number) RISE NANO PRINTING & ASSEMBLING MANUAL © PLANEPRINT...
- Page 25 3D printing Always keep the transmitter switched on when the model will not be replaced by PLANEPRINT.com in any way. is switched on. When operating, always keep a safe distance from your Always remove the battery before disassembling the model.
Need help?
Do you have a question about the RISE nano and is the answer not in the manual?
Questions and answers