Full Gauge Controls Wall-Fi Manual

MICROSOL II PLUS AND
1 - DESCRIPTION
Wall-Fi is an interface intended to be used together with Microsol II plus from version 2. It enables
easy and quick remote access to all Microsol II information and setup.
(1)
Compatible with Microsol II plus or Microsol II power
2 - APPLICATION
Solar heating controlling.
3 - TECHNICAL SPECIFICATIONS
- Power supply: 90 - 264 Vac (50/60 Hz)
- Size: 90 x 131 x 28 mm (W x H x D)
- Operating temperature: 0 to 50°C
- Operating humidity: 10 to 90% RH (no condensation)
- Data communication: By radio frequency - maximum distance of 50 meters without obstacles
-Routers: For installations requiring the use of the FG-Wi Router, a maximum of 16 routers can be
installed.
4 - MAIN SCREEN
The figure below shows the main screen of Wall-Fi with the system in operation.
Preferential indication
description
Swimming pool
26.9$C
Preferential indication
value
5 - FUNCTION MENU
The function menu allows configuring Microsol II controller functions remotely. To access the function
menu press and keys simultaneously for two seconds until the functions are shown in the
display. To access any function and confirm the value press
leave any function without confirming press
menu:
01- Access Code 03-Schedule Mode
02- Functions 04-Schedule Evt
5.1 - Access code
The access code 123 must be entered in this screen to enable changing functions of Microsol II
controller. To enter the code press on the message and adjust the value that will be blinking on the
display. Press again to confirm; to cancel and go back press
5.2 - Functions
In this screen all functions of Microsol II can be adjusted. To make changes press (1)
function and enter the value that will be blinking on the display. Press
value; to cancel and go back press .
On Dif Temp
Function
description
dOn@ 10.0 #
Function code
Function value
5.3 - Event scheduling mode
(1)
The operating mode of Microsol II event scheduling can be programmed from this screen.
5.4 - Event scheduling
The schedule of the instrument can be viewed and changed by accessing this function with the key
. To inform or change the configuration press
day of the week. Adjust the time of beginning and end of the event using the
to confirm the new value; to cancel and go back press
To go back or to leave the options press
Monday
Day of week
E02@ 09:40/18:50
Day event
Start time
5.5 - Clock adjustment
(1)
To adjust the internal clock of Microsol II select this function by pressing
using the and and press to confirm or
press at any time.
6 - QUICK ACCESS MENU
The quick access menu allows configuring the setpoints of supports 1 and 2, as well as the manual
operating modes and the overheating temperature for sensor 2. To access this menu, press
while Wall-Fi main screen is displayed. To access any function and confirm the value press
REMOTE USER INTERFACE FOR
MICROSOL II POWER
Ver.05
(1)
(1)
; to go back to the previous menu or to
. The following options are available in the function
05-Clock
.
on the desired
again to confirm the new
Function unit
on the option corresponding to the event and
and
.
at any time.
Finish time
. Then adjust the values
to cancel. To go back or to leave the options
back to the previous menu or to leave any function without confirming press
are available in the function menu:
01-Setpoint A1
02-Setpoint A2
03-S2 Hi Temp
Only with Microsol II plus version 03 or
Only with Microsol II power version 01
6.1 - Auxiliary 1 setpoint
This function allows adjusting the control temperature for auxiliary output 1.
6.2 - Auxiliary 2 setpoint
This function allows adjusting the control temperature for auxiliary output 2.
6.3 - Sensor 2 overheating temperature
This function allows adjusting the overheating temperature for sensor 2. When applied to swimming
pools this is the limit temperature of the water (comfort temperature)
6.4 - Water pump operating mode
This function allows adjusting the manual operating mode of the water pump.
6.5 - Auxiliary 1 manual mode enable
The operating mode of the auxiliary 1 output can be toggled between manual and automatic by
pressing on this function.
6.6 - Auxiliary 2 manual mode enable
The operating mode of the auxiliary 2 output can be toggled between manual and automatic by
pressing on this function. Note: This option will be only available for Microsol II plus from version
03 or Microsol II power from version 01.
6.7 - Viewing the minimum and maximum temperatures
(
only available for
Pressing the
each sensor of Microsol II power.
7 - ACCESS MENU FOR ADJUSTING THE CONNECTION
Upon accessing the quick access menu while Wall-Fi is not connected to the Microsol II , the user will
have two functions available for adjusting the address of the instrument:
(1)
01-McSol 485 Add
7.1 - McSol 485 Add (Microsol II
The address of Microsol II controller can be manually adjusted by entering this function. The value of
this function must be the same value configured in Microsol II .
7.2 - Search McSol (Search Microsol II )
on this function makes Wall-Fi start searching for Microsol II address automatically.
Pressing
Enter the quick access menu again to stop the automatic search.
8 - SETUP MENU
The operating characteristics of Wall-Fi can be adjusted through the setup menu. To access the
function menu press
in the display. The following options are available in the setup menu:
01-McSol 485 Add
02-Interface
keys, press
03-Descriptions
8.1 - McSol2 485 Add (Microsol II
This function allows to manually adjusting the address of the Microsol II controller.
The value set for this function should be the same value set on the Microsol II .
8.2 - Interface
Allows adjusting the user interface characteristics:
Fun
I01
Indication
I02
Language (Port, Engl, Esp)
I03
Display contrast
I04
Display timeout
shortly
I05
Sound signaling
; to go
04-Pmp Activat
05-A1 Man Mode
06-A2 Man Mode
higher
Microsol II power)
key in this function you can browse the minimum and maximum temperatures for
02-Search McSol
(1) address)
(1)
(1)
(1)
and keys simultaneously for eight seconds until the functions are shown
04-Timeouts
05-RF Config
06-Router Add
(1) address)
Description
Min.
S1
Off
. The following options
07- Min max Temp
(1)
(1)
07-Routes
08-Statistics
(1)
(1)
Max. Unit Default
All - S2
- - - Port
1 10 - 5
0 999 min. 0
On - Off