Download Print this page
Endura 3920PA15 Installation & Operation Instructions

Endura 3920PA15 Installation & Operation Instructions

Advertisement

Available languages

Available languages

Quick Links

INSTALLATION & OPERATION INSTRUCTIONS
Thank you for purchasing the Endura Plaster Trap. This
unit is intended for a wide range of applications where
by gravity, material is required to be separated from the
waste water flow. This includes materials such as plaster,
clay, sand, sediment, grit and general debris.
This unit is designed for use with inlet waste connections up to 1½" diameter
the inlet connection being made with a flexible no-hub coupling (not
supplied). Based on the outside diameter of the inlet/outlet these fittings
will need to be either 2" x 1 ½" or 2" x 1 ¼" reducing style couplings and are
available from most plumbing wholesalers or DIY outlets.
DO NOT decrease the pipe diameter across the unit – i.e. inlet vs. outlet.
Please Note : The Endura Plaster Trap is made of polypropylene which
will not accept solvent weld cement.
Based on the use of 1½" pipe the maximum flow rate that can enter and pass
through this unit is 20GPM.
Unlike a grease interceptor no flow control device is necessary in this
application.
ASSEMBLY
In reading these instructions you have already opened the tank and found
inside a carton
containing the following components.
A
A) 1 x inlet adaptor
B) 1 x 4 ¾" length of pipe
C) 1 x Access Tee
D) 1 x Access Tee Cap
E) 1 x Outlet adaptor
For assembly you will require:
• Solvent Cement suitable for ABS material
• Wood block or suitable alternative
• Hammer
GD-01031-06-18
3920PA15-3
C
D
B
Technical Support
tech-support@endurainterceptor.com
Endura® is a registered trademark.
INSTALLATION
Working from the outside of the tank with the cover removed, take the inlet
adaptor (A) and insert the chamfered end (smaller diameter) into the inlet
opening. With the block of wood (or suitable alternative) to protect the
adaptor flange, using the hammer tap the adaptor into the inlet until the
flange stops against the face of the tank spigot.
With the access cap of the tee facing the tank outlet and the lower connection
of the tee pointing toward the bottom of the tank, solvent weld the tee (C)
onto the spigot of the adaptor that now extends inside the tank inlet. Using a
proprietary ABS cement.
Now solvent weld the length of pipe (B) supplied into the lower connection of
the tee.
E
Finally take the outlet adaptor (E) and push into the opening of the outlet.
Note: This is an interference fit only - no cement required.
SERVICING AND MAINTENANCE:
Your Endura Plaster Trap will require periodic servicing to remove accumulated
material and maximize its ongoing effectiveness. This process can be achieved
manually by bailing out excess water, collecting accumulated debris to a
suitable container by hand for disposal/re-use, or using a suitable wet vacuum
extraction unit. Alternatively a contractor can be usually found locally who
can use an industrial vacuum method to remove and dispose of the entire
contents on a regular basis.
Ensure that you check the outlet screen during this process and clean the filter
mesh accordingly. It will be necessary to check the operation of the Plaster
Trap on a weekly basis for the first 6-8 weeks following commissioning. This
will allow you to assess the on going schedule of maintenance.
Canada
Tel: (705) 726-3361
1-800-461-1771
Fax: (705) 726-2186
3920PA15
U.S.A.
Tel: (303) 373-1918
1-888-461-5307
Fax: (303) 373-1923
3910PA15

Advertisement

loading
Need help?

Need help?

Do you have a question about the 3920PA15 and is the answer not in the manual?

Questions and answers

Summary of Contents for Endura 3920PA15

  • Page 1 DIY outlets. 3920PA15 DO NOT decrease the pipe diameter across the unit – i.e. inlet vs. outlet. Please Note : The Endura Plaster Trap is made of polypropylene which will not accept solvent weld cement. INSTALLATION Based on the use of 1½”...
  • Page 2 NE RÉDUISEZ PAS le diamètre du tuyau de l’installation, c’est-à-dire, l’entrée INSTALLATION par rapport à la sortie. Remarque : Le séparateur de plâtre Endura fait de polypropylène; par conséquent, vous ne devez pas l’utiliser avec Travaillez de l’extérieur du réservoir dont vous avez retiré le couvercle. Insérez un adhésif à...

This manual is also suitable for:

3910pa15