Ruroc EOX SHOCKWAVE BT Instruction Manual
  1. Manuals
  2. Brands
  3. Ruroc Manuals
  4. Motorcycle Accessories
  5. EOX SHOCKWAVE BT
  6. Instruction manual

Ruroc EOX SHOCKWAVE BT Instruction Manual

Hide thumbs

Advertisement

Table of Contents

INSTRUCTION MANUAL
MODEL NAME: RUROC SHOCKWAVE BT

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EOX SHOCKWAVE BT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ruroc EOX SHOCKWAVE BT

Summary of Contents for Ruroc EOX SHOCKWAVE BT

  • Page 1 INSTRUCTION MANUAL MODEL NAME: RUROC SHOCKWAVE BT...
  • Page 2 2. If local law prohibits the use of headphones while riding, do not use. If you do not comply with this warning, Ruroc does not accept any liability. 3. Use of this product at a high volume for a long time may cause damage to your ears &...

  • Page 3: Warranty Information

    If a Ruroc product fails due to defects 2. Safe startup: be sure to use your in craftsmanship or materials, within product in a safe environment as...
  • Page 4 FITTING YOUR SHOCKWAVE 1. Remove the Snap-Fit Bluetooth cover on both sides of the helmet. Keep these covers stored securely should you wish to re-use them in the future. REMOVE 2. Insert Battery into side [A] by lining up the locators with slots in the battery cavity, press until it ‘CLICKS’.

  • Page 5: Connecting Your Speakers

    CONNECTING YOUR SPEAKERS Gently release the poppers on the cheek pads and remove them from the helmet. 2. Plug the Mic+Speaker cable [C] into the AUX jack port on the helmets left side (right side of below diagrams). 3. Plug the Speaker-only cable [D] into the AUX jack port on the helmets right side (left side of below diagrams)
  • Page 6 FITTING YOUR SPEAKERS Attach each of the Shockwave speakers where Velcro [E] is located (in the orientation shown in the diagram) 2. Attach the Shockwave Mic where Velcro [F] is located to the side of the chin vent (in the orientation shown in the diagram) 3.
  • Page 7 SHOCKWAVE BASICS Press the Intercom Button & Media Button for 1 second to switch on the Shockwave system, you TURN ON will hear a “Power On” message Press the Intercom Button & Media Button for 1 TURN OFF second to switch off the Shockwave system, you will hear a “Power Off”...

  • Page 8: Bluetooth Connection

    BLUETOOTH CONNECTION • When connecting the Shockwave system to your device for the first time*, hold the SELECT/PHONE BUTTON** for 5 seconds until you hear ‘pairing’. • The LED will flash RED & BLUE as the Shockwave looks for a connection device •...
  • Page 9 • You will hear the message ‘Connected’ to confirm the connection, and the BLUE LED with flash once periodically while the devices remain paired. *Your Shockwave will automatically connect to a previously connected device (within range) when powered on. **If the unit is already on, pressing the SELECT/PHONE BUTTON [C] for 5 seconds will put the unit into pairing mode.

  • Page 10: Audio Control

    AUDIO CONTROL • When connected, to start/play a track press the MEDIA BUTTON once. (your music app must be open) To skip track forward, press the MEDIA BUTTON once. • • To skip track backwards, press the INTERCOM BUTTON once.
  • Page 11 • To turn the volume up, press or hold the VOLUME UP BUTTON. • To turn the volume down, press or hold the VOLUME DOWN BUTTON. • To pause/stop music, press the SELECT/PHONE BUTTON once. • To resume music, press the MEDIA BUTTON once.
  • Page 12 INTERCOM RIDER-PILLION • When connecting two Shockwave units for the first time, put both units into Bluetooth® pairing mode by holding the INTERCOM BUTTON for 5 seconds. • Once in pairing mode, the LED will flash periodically between Red & Blue to show that it is in pairing mode and you will hear the message ‘Pairing State’.
  • Page 13 • Successful connection will cause the LED to flash BLUE periodically on both SHOCKWAVE units to indicate a successful connection. • Once in pairing mode the LED will flash periodically between Red & Blue to show that it is in pairing mode and you will hear the message ‘Pairing State’.
  • Page 14 MAKE/RECEIVE CALLS If the Shockwave is connected to a phone and a number is dialled, it will automatically direct the call through the speakers and activate the microphone. When the connected phone has a call incoming the Shockwave will cut any music/ intercom audio and the call will ring through the speakers.

  • Page 15: Voice Assistant

    • To cancel or end the call, press either the SELECT/PHONE BUTTON or INTERCOM BUTTON or MEDIA BUTTON once. ANY OF THE ABOVE 3 BUTTONS To call the last dialled number, press the SELECT/PHONE BUTTON X2 times. • VOICE ASSISTANT To activate your phones voice assistance features, simply hold the SELECT/PHONE BUTTON for 2 seconds.

  • Page 16: Fcc Regulatory Compliance

    Class B digital device, pursuant to Part 15 of the FCC Rules. Hereby Ruroc Ltd declares that this product is in compliance with essential These limits are designed to provide requirements and other relevant reasonable protection against harmful provisions of Directive 2014/53/EU.

  • Page 17: Ised Compliance Statement

    ISED COMPLIANCE STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: • This device may not cause interference. • This device must accept any interference, including interference that may cause undesired operation of the device.

  • Page 18: Specification

    ATTENTION SPECIFICATION Installing equipment on the helmet is BLUETOOTH® VERSION: DUAL-MODE BT 5.3 WITH LE AUDIO a modification of the helmet, which may cause the helmet’s warranty to SUPPORT: fail or hinder the helmet's function. STAR-MC1 PROCESSOR, BECO This may cause danger in the event of COPROCESSOR accidents.

Table of Contents