Grote STAR S-LINK 9200 HALO Series Manual

9200 HALO Series LED Mini-bars
IMPORTANT: Please read all of the following instructions before installing your new warning light.
Please Note: These instructions are provided as a general guideline only. Specific
mounting and/or wiring, may be necessary and are the sole responsibility of the
installer. Star Safety Technologies assumes no responsibility for the integrity of
the installation for this or any of its products.
LED FIVE YEAR LIMITED WARRANTY
Star Safety Technologies warrants this LED light against factory defects in material and workmanship
for five years after the date of manufacture. The owner will be responsible for returning to the Service
Center any defective item(s) with the transportation costs prepaid. The manufacturer will, without
charge, repair or replace at its option, products, or part(s), which its inspection determines to be
defective. Repaired or replacement item(s) will be returned to the purchaser with transportation
costs prepaid from the service point. A copy of the purchaser's receipt must be returned with the
defective item(s) in order to qualify for the warranty coverage. Exclusions from this warranty include,
but are not limited to, domes, and/or the finish. This warranty shall not apply to any light, which has
been altered, such that in the manufacturer's judgment, the performance or reliability has been
affected, or if any damage has resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness),
which extend this warranty period. The loss of use of the product, loss of time, inconvenience,
commercial loss or consequential damages, including costs of any labor, are not covered. Star
reserves the right to change the design of the product without assuming any obligation to modify any
product previously manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from
state to state. Some states do not allow limitations on how long an implied warranty lasts. Some
states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the
above limitation(s) or exclusion(s) may not apply to you.
If you have any questions concerning this or any other product, please contact our
Customer Service Department at (585) 226-9787.
If a product must be returned for any reason, please contact our
Customer Service Department to obtain a Returned Materials Authorization
number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.
Due to continuous product improvements, we must reserve the right to change any specifications and information,
contained in this manual at any time without notice. Star Safety Technologies, Inc. makes no warranty of any kind
with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Star shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this manual.
455 Rochester Street
585-226-9500
www.StarSafetyTechnologies.com
featuring the
NOTICE
Avon, NY 14414
(F) 888-478-2797
PLIT453 REV. D
If you are mounting the light on the roof of your vehicle, take extreme care to ensure that the magnet is
firmly seated on your roof, and that the pull of the magnet is sufficient to secure the light in place. As
the composition of the metal in the roofs of different vehicles may vary, as well as the contour, texture
and/or condition, Star cannot guarantee the ability of the light to remain in place upon a moving vehicle.
It is the sole responsibility of the owner to ensure the warning light is secure.
WARNING!!!! Care should be taken when positioning any warning light on the roof,
• CAUTION: Please be sure to check that your cigarette plug outlet is properly fused.
Testing the light before this fuse is properly installed will void the warranty on
the light.
• Once the light is secured, route your cord such that it does not interfere with the
vision of the driver or the operation of any controls, including, but not limited to, the
steering wheel, gear shifter, and/or airbag.
• This light has been factory tested and approved. If the light fails to work when the
plug is inserted into the cigarette plug socket, twist the plug a few times to remove
any ash or other deposits which might be preventing a good contact from being
made. If the problem persists, check for a fuse inside of the plug itself. If present,
remove the fuse from the circuit, check to see if it has blown, and clean the lighter
socket and contact surfaces. Reconnect the fuse and test the light again.
1. CAUTION: All of our DC powered warning lights are polarity sensitive. These lights
are polarity protected only if the appropriate fuse is used. All wires connected to the
positive terminal of the battery should be fused at the battery for their rated load.
Testing the light before this fuse is properly installed will void the warranty on
the light.
2. Remove the dome from your mini-bar. Take care not to damage the gasket. Place
the light in the exact position it is to be mounted.
3. Using the base as a template, mark four holes on the mounting surface. Take care to
ensure that the base does not move while you are marking each of the four holes.
4. Remove the base and drill a 3/8" hole in the four marked spots.
CAUTION: Take care not to drill through the headliner below.
5. Push the enclosed rubber well nuts through the holes until the bottom side of the
wider lip rests on the surface of the vehicle.
6. For external wiring of your new Star mini-bar skip to Step 8. For internal wiring,
proceed as follows: Remove the headliner from the inside of the vehicle. Draw two
diagonal lines between the well nuts in the opposite corners. Mark the location at
which they cross. Drill a 3/8" hole in the center marked location. Place the light on
the surface of the vehicle, routing the wires through the hole. Align the four other
holes with the well nuts, install the screws, and tighten until snug. Skip to Step 8.
7. For external wiring, place the light on the mounting surface and align the holes with
the well nuts. Install the screws and tighten until snug.
8. Replace the dome on your mini-bar.
2/22/24
Magnet Mounting
dash, or instrument panel of the vehicle, so that the light and/or cord
does not interfere with the proper operation of any airbags! Failure to
heed this warning may result in serious or fatal injury.
Permanent Mounting
-1-