V-Show Journey T912 User Manual
  1. Manuals
  2. Brands
  3. V-Show Manuals
  4. DJ Equipment
  5. Journey T912
  6. User manual

V-Show Journey T912 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
T912Journey
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Journey T912 and is the answer not in the manual?

Questions and answers

Related Manuals for V-Show Journey T912

Summary of Contents for V-Show Journey T912

  • Page 1 T912Journey User Manual...

  • Page 2: Safety Instructions

    1. Safety Instructions Please read the instruction carefully which includes important information about the installation, usage and maintenance. Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction manual. Important: Damages caused by the disregard of this user manual are not subject to warranty.

  • Page 3: Installation

    Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off the mains power immediately. DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly. DO NOT touch any wire during operation as there might be a hazard of electric shock.

  • Page 4: Installations

    2.INSTALLATIONS installations Note: In order to increase protection, please install the lamp on the sidewalk, outside the seating area, or an area where unauthorized persons may touch the lamp Before installing the fixture on any surface, make sure that the installation area can bear the minimum point load above 10 points of the weight of the equipment.

  • Page 5: Dmx-512 Control Connections

    3. DMX-512 control connections Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving heads be connected together through serial linking. The cable needed should be two core, screened cable with XLR input and output connectors.

  • Page 6: Address Code Setting

    4.Address code setting If you use a universal DMX controller to control the units, you have to set DMX address from 1 to 512 so that the units can receive DMX signal. Press the MENU button to enter menu mode, select DMX Settings, press the ENTER button to confirm, use the UP/DOWN button to select DMX Address, press the ENTER button to confirm, the present address will blink in the display, use the UP/DOWN button to adjust the address from 001 to 512, press the...
  • Page 7 6.Illuminance chart: 7. Effect Wheels Color...
  • Page 8 Fixed Gobo Rotation Gobo...

  • Page 9: Light Source

    Prism Frost 8.Light Source MSD Silver 380W/2 LL Because of its high internal pressure, there might be a risk that the Discharge lamp would explode during operation. The lamp emits intense UV radiation which is harmful to the eyes and skin. The high luminance of the arc can cause severe damage to the retina if you take a close look at the lamp.
  • Page 10 9.Lamp technical parameters Input Voltage: 100-240V, 50/60Hz Output Voltage: V1:36V2A(Master board), V2:12V4A(cooling fan) , V3:380V1A(lamp) Power consumption: 520 W Power supply: 600W Light source: PHILIPS MSD Silver 380/2 LL (4000 hours) Color temperature: 7800K CRI：80 Diameter of optic lens: 128mm Beam angle: 2°-50°...
  • Page 11 uniform, and the wash mode is soft. Coupled with linear CMY colors, it achieves infinite color change. The rich colors and patterns provide excellent color macro and dynamic effects, equipped withTwo prisms (6and8) effect, Create more rich and colorful stage visual effects, not only with a compact appearance, but also with a fashionable and lightweight design, suitable for various occasions.

  • Page 12: Menu Settings

    11.Menu settings Third Fourth Main First level Secondary level level Menu menu menu menu menu DMX Address 000-255 Auto SET UP user Slave Master LAMP DMX LAME Auto Safety Black Out Invrt pan Pan/Tilt Invrt Tilt Encoder pan-Tilt 30sec Sleep 2min OPTION 10min...
  • Page 13 clear ALL xxxx SYSTEM ERRORS LAPM Hours :000 LAMP reser lamp input xxxx INFORMATIO hours chn01 DMX monitor chn31 product code xxxxx factory test xxxxx LAMP Motor power reset All pan tilt RESET MANUAL color CONTROL gobo beam path C:000 M:000 Channel Y:000...
  • Page 14 12. DMX512 31CH DMX Value ILLUSTRATE CYAN 0-255 Color saturation from small to large MAGENTA 0-255 Color saturation from small to large YELLOW 0-255 Color saturation from small to large Color Wheel 1 0-23 empty 24-69 Color1 70-115 Color2 116-162 Color3 163-208 Color4...
  • Page 15 252-255 Lamp on dimmer 0-255 Dimming from 0% to 100% Dimmer fine 0-255 fine GOBO empty GOBO 1 8-11 GOBO 2 12-14 GOBO 3 15-18 GOBO 4 19-22 GOBO 5 23-26 GOBO 6 27-29 GOBO 7 30-33 GOBO 8 34-37 GOBO 9 38-41 GOBO 10...
  • Page 16 240-244 Gobo 16 shakes， speed from slow to fast 245-249 Gobo 17 shakes， speed from slow to fast 250-255 Gobo 18 shakes， speed from slow to fast No Effect No Effect Rotating GOBO empty 5-12 GOBO 1 13-20 GOBO 2 21-28 GOBO 3 29-36...
  • Page 17 8 FACET PRISM 0-127 Prism out 128-255 Prism IN Prism 2positioning and rotation 0-127 Prism 2 positioning and rotation 128-190 Prism 2CCW rotation , from fast to slow 191-192 Stop rotation 193-255 Prism 2CW rotation , from fast to slow Frost 0-64 empty...

  • Page 18: Troubleshooting

    LAMP To achieve the following effect, push the DMA value to the corresponding position and rest for at least 4 seconds 0-25 empty 26-100 LAMP OFF 101-255 LAMP ON 13. Troubleshooting The following are some of the problems that often occur when the device is running, along with some suggestions for troubleshooting: A.

  • Page 19: Equipment Cleaning

    14. Equipment cleaning Keeping the luminaire clean is absolutely necessary to maintain the best performance of the luminaire and ensure the best light effect. Lamps must be cleaned regularly to avoid Dust, dirt and fume residues accumulate on or inside the luminaire, and the frequency of cleaning depends on the application environment.

Table of Contents