Table of Contents
Advertisement
Quick Links
Smart Building Hub (SBH300)
The Smart Building Hub (SBH300) is the base controller for the Verasys™ Building Automation
System (BAS) and provides wired and wireless connection between all Smart Equipment layers and
Verasys controls. Use this guide to complete the following tasks:
•
Connect BACnet
MS/TP devices
®
•
Connect the TMR coordinator
•
Power the SBH300
•
Log on to the SBH300 local UI
•
Configure the Internet connection
Table 1: Factory default parameters
Wi-Fi AP SSID: VERASYS-SBH
Wi-Fi AP Passphrase: Place label here
UI Username: admin
UI Password: Place label here
Device ID: Place label here
Note: Save this guide. It contains your default username and password information needed to
access this device after a network reset.
Connecting BACnet Equipment to the SBH300
About this task:
When the SBH300 is connected to a MS/TP network through a wired connection or a wireless TMR
connection, you can access Verasys controllers and third-party BACnet MS/TP devices. The SBH300
connects to the MS/TP network through the System Bus.
To view a device on the network to see its setpoints, alarms, and other parameters, use a web-
enabled device with a supported internet browser connected to the SBH300 Wi-Fi network.
1.
To connect the SBH300 to the Verasys System, use the four-terminal System Bus port. Wire
the System Bus communications to the blue four-terminal connector.
2.
If the SBH is at the end of a line, set the end-of-line (EOL) switch to ON.
3.
Connect the Wi-Fi adapter to one of the USB ports.
Connecting a TMR coordinator
You can connect equipment over a MS/TP wireless network to the SBH300 with a TMR set to
coordinator mode. You can connect up to two TMRs in Coordinator Mode to the SBH300. The first
TMR connected to the System Bus of the SBH300 automatically resets to Coordinator Mode. When
you connect a second TMR to the SBH300, you must manually set the TMR to Coordinator Mode. For
Part No. A16381V57K Rev. C
2024-03-28
Verasys Smart Building Hub (SBH300)
Quick Start Guide
*A16381V57KC*
(barcode for factory use only)
LC-SBH300-0, LC-SBH300-0C, LC-SBHPNL-01
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Verasys SBH300
Summary of Contents for Verasys SBH300
- Page 1 You can connect up to two TMRs in Coordinator Mode to the SBH300. The first TMR connected to the System Bus of the SBH300 automatically resets to Coordinator Mode. When you connect a second TMR to the SBH300, you must manually set the TMR to Coordinator Mode. For Part No. A16381V57K Rev. C...
- Page 2 Bus Cable section of the Verasys BACnet MS/TP Communications Technical Bulletin (LIT-12012362). Note: If the System Bus starts at the SBH300, connect the shield to earth ground. If the SBH is in the middle of the run, wire nut the shields together and bypass the SBH300.
- Page 3 Smart Building Hub (SBH300) Quick Start Guide (Part No. A16381V57K) included with the SBH300. Read and accept the SBH300 license agreement. The first time you log on to the SBH300, you must change the admin password, Wi-Fi AP Passphrase, and the Wi-Fi AP SSID.
- Page 4 Configuring the Internet connection Wi-Fi Client Before you begin: The SBH300 Wi-Fi Client uses the WPA2-PSK protocol. Ensure that the external Wi-Fi router is set to WPA2-PSK mode. Do not turn Wi-Fi Client and Ethernet on at the same time. When you use the Wi-Fi Client, make sure that Ethernet is off.
- Page 5 From the SSID list, select the SSID of the wireless network you want to connect to. Note: Ensure the SSID of the wireless network does not contain special characters, such as ',*,@,$,!,#. Special characters prevent the SBH300 connecting to wireless networks.
- Page 6 Airwall Commissioning for SBH300 remote access Before you can remotely access the SBH300, you must first commission the Airwall Agent. The Airwall Agent provides remote access to the SBH300 from anywhere and secures your connection with industry standard Zero Trust Based Security.
-
Page 7: Related Documentation
Related documentation The following table contains a list of the related Verasys documents. View Verasys documentation at https://docs.johnsoncontrols.com/bas/. Table 3: Verasys documentation Information Refer to Verasys Smart Building Hub (SBH300) Installation Guide Installing the SBH300 SBH300 (LIT-12014293) Verasys System Product Bulletin (LIT-12012342) - Page 8 ® ® Safari version 14 or later. ® Handheld device: Microsoft Edge version 91 or later. Google Chrome version 91 or later. Mozilla Firefox version 90. Apple Safari version 14 or later. Verasys Smart Building Hub (SBH300) Quick Start Guide...
-
Page 9: North American Emissions Compliance
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that Verasys Smart Building Hub (SBH300) Quick Start Guide... -
Page 10: Product Warranty
2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Product warranty This product is covered by a limited warranty, details of which can be found at www.johnsoncontrols.com/buildingswarranty. Patents Patents: https://jcipat.com Verasys Smart Building Hub (SBH300) Quick Start Guide... -
Page 11: Contact Information
NO. 32 CHANGJIANG RD NEW THE NETHERLANDS MANCHESTER DISTRICT M40 2WL WUXI JIANGSU PROVINCE UNITED KINGDOM 214028 CHINA Contact information Contact your local Johnson Controls representative: www.johnsoncontrols.com/locations Contact Johnson Controls: www.johnsoncontrols.com/contact-us Verasys Smart Building Hub (SBH300) Quick Start Guide... - Page 12 © 2024 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and are subject to change without notice. www.johnsoncontrols.com...
Need help?
Do you have a question about the SBH300 and is the answer not in the manual?
Questions and answers