BeiJer JetNet 3008 Series Quick Installation Manual

JetNet 3008/3008f Series Industrial Ethernet Switch
Quick Installation Guide V1.7
Overview
JetNet 3008/3008f Industrial Ethernet Switch, supports 8 10/100Base TX (JetNet 3008) or 6
10/100TX plus two 100FX Fast Ethernet ber ports in either multi-mode type (JetNet
3008f-m) or single-mode type (JetNet 3008f-s). e JetNet3008/3008f adopts rugged metal
case design to operate in harsh environments (-40~75°C JetNet 3008-w/3008f-w); It also
provides IP-30 standard protection. It features one relay output to alarm users if a port link fails
or with the power fails. Alarms can be enabled/disabled by a 9-pin dip switch. JetNet
3008/3008f is recommended to be powered by DC 12V or 24V with 10~60V range from the
6-pin removable terminal block.
Package Check List
 JetNet 3008/3008f Switch
 Quick Installation Guide
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetNet 3008/3008f on the DIN rail.
Grounding JetNet Switch
Earth Ground
There is one grounding screw on the bottom
Screw
side of JetNet 3008/3008f. Connect the earth
ground screw of switch to the grounding
surface to ensure safety and prevent noise. See,
Earth Ground
Figure-1
Warning: Do not connect to AC line-Natural
Wiring the Power Inputs
1. Insert the positive and negative wires into
the V+ and V- contact on the terminal
block connector.
2. Tighten the wire-clamp screws to prevent
the DC wires from being loosened. See
Figure-2
Notes: e recommended working voltage is DC 12V or 24V (DC10~60V, 0.8A).
Wiring the Relay Output
The relay output alarm contacts are in the
middle of the terminal block connector as
shown in the figure below.
By inserting the wires and set the DIP switch of
the respective Port Alarm to "ON", relay
output alarm will detect any port failures, and
form a short circuit.
The alarm relay output is "Normal Open". See, Figure -3.
Connecting to Network
1. Connecting the Ethernet Ports: Connect one end of an Ethernet cable into the UTP port
of JetNet 3008/3008f, while the other end is connected to the attached networking device.
All UTP ports support auto MDI/MDIX function.
link and turn of for 10Mbps link, the LNK/ACT LED will turn on for link up and
blinking for packet transmit and receive.
Activity.
2. Connecting the Fiber Port (JetNet 3008f ): Connect the ber port on your JetNet 3008f
to another Fiber Ethernet device, by following the gure below. Wrong connection will
cause the ber port not working properly.
ATTENTION
This is a Class 1 Laser/LED product.
!
Don't look into the Laser/LED Beam.
Figure-1
DIP Switch Settings for Alarm Relay Output
Alm
PW1 PW2
Alarm Control
port 1~8 power
Pin No. # Status Description
ON
P1 to P8
(Pin1~8)
Off
ON
P9
Off
Figure-2
Figure-3
Maximum 1A current / DC 24V
Alm
PW1 PW2
Alarm Control
port 1~8 power
e Speed LED will turn on for 100M
e ber port only support 1 LED for Link and
RX
TX
Cable Wiring(SC to SC)
TX A
RX A
To enable port link down alarm at this port
To disable port link down alarm at this port
To enable power failure alarm
To disable power failure alarm
Support
Alarm
5 Years Warranty
System
Each of Beijer Electronics 's product is designed, produced, and tested with high industrial
standard. Beijer Electronics warrants that the product(s) shall be free from defects in materials
Extra Power
and workmanship for a period of ve (5) years from the date of delivery provided that the
System
product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted product are caused
by damage resulting from force measure (such as oods, re, etc.), other external forces such
as power disturbances, over spec power input, or incorrect cabling; or the warranted product is
misused, abused, or operated, altered and repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment (RoHS Directives & RoHS 2.0)
RX
TX
RX B
TX B