Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LASER TECH TruPulse 200X
Summary of Contents for LASER TECH TruPulse 200X
- Page 1 200X ® ulse uick eference ield uide LTI Part #0144893...
- Page 2 TruPulse 200X ® Fire Button LTI Technical Support Down Button Toll Free: 1.877.696.2584 Mode Button Phone: 1.303.649.1000 Up Button Email: servicecenter@lasertech.com Web: www.lasertech.com LTI Hours of Operation Monday through Friday 8:00 am to 5:00 pm (MST) (Excluding Holidays) LTI Corporate Headquarters LTI YouTube Channel ®...
- Page 3 Closest Inclination TruPulse 200X ® Display Indicators: Farthest Gate Continuous Slope Distance Filter Horizontal Feet Distance Inches Vertical Distance Upper and Lower Meters Main Display Missing Line Centimeters Cross hair / Aiming Point Height Yards Battery Life Degrees Laser Status Percent...
- Page 4 TruPulse 200X Measured by TruPulse: ® Values & Key Code: Calculated by TruPulse: 1-Shot Distance: 2-Shot Missing Line: = Horizontal Distance = Slope Distance = Vertical Distance = Height = Inclination = Missing Line 2-Shot Height: 3-Shot Height: = Fire Button = Mode Button = Forward Button = Back Button...
- Page 5 Change Display Brightness Level: [1] Press until . [2] Press until desired brightness level . [3] Press to accept the brightness level. Change Units of Measurements: [1] Press until [2] Press to scroll through unit options [3] Press to accept the units of measurement The default units of measurements are meters, Helpful Tip: centimeters and degrees.
-
Page 6: Filter Mode
Filter Mode: [1] Press until . [2] Press to choose . [3] Press to accept selection. Continuous Mode: [1] Press until . [2] Press to choose [3] Press to accept selection. Helpful Tip: When Filter mode is ON, make sure you have the foliage filter attached to the receive lens and that you are shooting to a reflective target. -
Page 7: Helpful Tips
Targeting Mode: [1] Press until . [2] Press to choose mode: Standard ; Farthest ; Closest [3] Press to accept selection. Helpful Tips: [1] Targeting mode is not accessible when filter mode is on. [2] Filter symbol , continuous mode symbol and any other mode symbol will show on right side of the main display when activated. -
Page 8: Gate Function
Gate Function: In this mode, the TruPulse 200X will only acquire targets beyond the selected gate value. [1] Press until . [2] Press to choose on or off . [3] With Gate ON, press to change the value. [4] Press and release... - Page 9 Turn On or Off Bluetooth ® [1] Press until . [2] Press to choose Bluetooth on or EnC . [3] Press to accept selection. Helpful Tips: [1] Each time the TP200X is powered ON, it will retain the same settings that were last set/used.
-
Page 10: Measure Distance
Measure Distance: In HD Mode, it will automatically measure SD and INC, then calculate VD and HD. The values will output via serial and/or Bluetooth. Measurements are from the center of laser to target. [1] Press until is displayed. [2] Aim at target where you have a clear line of sight then long press [3] Press to scroll through SD... - Page 11 Measure Height in 3 Shots: This routine is ideal for flat, vertical objects that do not lean. To shoot through brush, use the Filter Mode, foliage filter and a reflector. [1] Press until is displayed. [2] Aim anywhere you have a clear line of sight and long press Aim to the bottom and long press...
- Page 12 Measure Height in 2 shots: The 2-shot HT works well on leaning objects but requires a clear line of sight for both shots. [1] Press until displayed. [2] Aim at the top of the target and long press . Note the value. [3] Aim to the bottom of the target and long press .
- Page 13 Measure 2-D Missing Line: Position yourself where shot 1 and 2 are made looking in the same direction with a clear line of site to both targets. The exception is the VD solution, which will always be accurate no matter which direction shot 1 and 2 are taken.
- Page 14 www.lasertech.com 1.303.649.1000 info@lasertech.com...
Need help?
Do you have a question about the TruPulse 200X and is the answer not in the manual?
Questions and answers