Val Controls IHP24-BF Hardware Manual
Hide thumbs
Also See for IHP24-BF:
- User manual (38 pages) ,
- Manual (58 pages) ,
- Hardware manual (13 pages)
Subscribe to Our Youtube Channel
Related Manuals for Val Controls IHP24-BF
Summary of Contents for Val Controls IHP24-BF
- Page 1 HARDWARE MANUAL IHP24-BF Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 1/11...
-
Page 2: Table Of Contents
Terminals ............................10 Electrical specifications ......................... 10 Digital input – DI9 ........................11 Terminals ............................11 Electrical specifications ......................... 11 Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 2/11... -
Page 3: General
IHP24-BF-300000 1.1 Safety instructions For a safe installation of a Val Controls device, the following must be observed. The module must be installed by qualified personnel who are familiar with the national and international laws, directives and standards that apply to this product as well as all instructions in this manual. - Page 4 The O-ring is as standard treated with Molykote 55 O-ring grease. To maintain the IP rating the O- ring has to be treated every 2 year with Molykote 55 O-ring grease or similar. Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com •...
-
Page 5: Communication
2 Communication There are two type of communication available HART and FF. For model: IHP24-BF-100000 go to 2.1 Control loopwith HART – AI0 and Transmitter loop – AO0. For model: IHP24-BF-300000 go to 2.2 Foundation Fieldbus. 2.1 Control loopwith HART – AI0 and Transmitter loop – AO0 Passive 4-20mA input and passive 4-20mA output. -
Page 6: Foundation Fieldbus
4 (FB-N) 2.2.2 Electrical specifications FF-Fieldbus FF-Fieldbus - H1 Device Class – Basic Device Interface Termination No internal termination Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 6/11... -
Page 7: Power Supply - Ps2
Power dissipation, no position sensor/loop or < 2W valves are connected. Power dissipation, with maximum load on all < 5W inputs and outputs Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 7/11... -
Page 8: 4-20Ma Input - Ai1
Cable length 1000 meters Linearity < 0.1% Temperature coefficient 0.01% / 1°C (Warm-up: 10 min) < 100 Ohm Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 8/11... -
Page 9: Position Sensor - Ai10
Minimum use operating area Cable length 1.5 meters Linearity < 0.1% Temperature coefficient 0.01% / 1°C (Warm-up: 10 min) Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 9/11... -
Page 10: Digital Output - Do1, Do2, Do3, Do4
Max load per digital output up to 48W at 24VDC Max load total up to 192W at 24VDC Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 10/11... -
Page 11: Digital Input - Di9
The external resistor must be mounted to get the correct functionality. 7.1 Terminals 8 (+) 6 (-) 7.2 Electrical specifications DI12 Type Switch Cable length 1.5 meters Val Controls A/S • Sallingsundvej 5 • DK-6715 Esbjerg N • Tel. +45 7547 0600 DHW-UM-014 Revision: 1 vc@valcontrols.com • www.valcontrols.com 11/11...
Need help?
Do you have a question about the IHP24-BF and is the answer not in the manual?
Questions and answers