Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Vaxcel Manuals
  4. Outdoor Light
  5. T0753
  6. Assembly and installation instructions

Vaxcel T0753 Assembly And Installation Instructions

Hide thumbs
1
2
3
4
5

Advertisement

Quick Links

Download this manual
ASSEMBLY AND INSTALLATION
T0753
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d'alimentation principale au panneau
central de disjoncteurs avant d'installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120V AC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the ground wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
8. Compatible with most LED dimmable bulbs.
Maximum Wattage: 60W Bulb
Working Temperature: - 22°F~113°F
Outlet Box
House Ground Wire
Fixture Mounting Screw
Green Ground Screw
Mounting Plate Unit (A)
Mounting Screw (B)
Fixture Ground Wire
Wire Connector (C)
Fixture Wire
Backplate
Max. 60W Type A Bulb
(not included)
INSTRUCTIONS
Socket Ring
Page 1 / 5
Features
1. Energy saving fixture.
2. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)：
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C)
Bolt Nut (D)
Rubber Pad (E)
Rubber Pad (E)
Bolt Nut (D)
Glass Shade
231115

Advertisement

loading

Related Manuals for Vaxcel T0753

Summary of Contents for Vaxcel T0753

  • Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0753 WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

  • Page 2: Installation Steps

    Installation Steps Turn off the power at fuse or circuit box 1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate. 2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary.

  • Page 3: Function And Operation

    Function and Operation MODES OF OPERATION Choose a mode by turning the rotary knob. The light will turn on immediately when power is applied. Wait for 30 seconds to allow the sensor to warm up. 1. Test MODE (daytime and nighttime operation.) ●...

  • Page 4: Troubleshooting

    Sensitivity of Motion Sensor Where you install your light is important: Be sure the light is mounted straight on the wall; 1. The sensitivity can be adjusted from 5 to 30 feet by using the otherwise, the detection distance may be limited. "Sens"...

  • Page 5: Spare Parts List

    Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.