Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0702 / T0703
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#6/32 X1/2 in
#8/32X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 40 W
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Swing the sensor head towards the back plate.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
13°F ~ 113°F
Controls
Page 1 / 5
Fixture Mounting Screw
Decorative cover
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
Low-level brightness when motion stops.
3. Photocell keeps the light OFF during daylight hours.
4. When in manual override mode, use wall switch
to keep the light ON during the night.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Wire Connector
Gasket
Controls
221021
Advertisement
Related Manuals for Vaxcel T0702
Summary of Contents for Vaxcel T0702
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0702 / T0703 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
-
Page 2: Installation Steps
FRONT Light Head Outlet Box Decorative cover Mounting Strap Sensor Wire Connector Backplate Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box. -
Page 3: Adjusting The Light Head
Sensitivity of Motion Sensor ● You can adjust the sensitivity of the motion sensor by using the “SENSITIVITY” selector located on the right side of the bottom surface of the sensor. (See Fig. 4) ● Adjust motion sensor sensitivity to achieve desired performance. ●... -
Page 4: Customization Options
4. 3 HOURS (3H) MODE (nighttime operation only) ● In “3H” mode, the light turns to high-level brightness (100%) at dusk, and stays "ON" for 3 hours, then it turns to low-level brightness. It turns to high-level brightness (100%) when motion is detected, and stays on as long as motion continues. -
Page 5: Troubleshooting
Wire Connector Gasket Mounting Strap Fixture Mounting Screw Decorative cover #10/24 X1/4 in #8/32X1/2 in #6/32 X1/2 in Assembly Kit 6615MM (1 SET) FOR T0702 6616MM (1 SET) FOR T0703 A: 7" B: 13-1/4" C: 6-1/4" Page 5 / 5 221021...