Related Manuals for LANGER EMV-Technik P512 Set
Summary of Contents for LANGER EMV-Technik P512 Set
- Page 1 Manual P512 Set RF power injection and RF measurement 2024-02-14 P512 Set Bedienungsanleitung Copyright © December 2023 LANGER EMV-Technik GmbH...
-
Page 2: Table Of Contents
Design and Function ......................9 Contact Detection ......................10 Operational Notes ...................... 11 Measurement setup ....................12 Direct power injection DPI (P512 Set) ................12 Measurements of RF signals (P512 HF-T set) ..............15 Technical Parameters ....................17 P512 Probe ........................17 Housing and probe tip dimensions .................. -
Page 3: Declaration Of Conformity
Langer EMV-Technik GmbH Nöthnitzer Hang 31 01728 Bannewitz Germany Langer EMV-Technik GmbH herewith declares that the P512 Set, RF Power Injection / RF Probe head with Probe P512 conforms with the following relevant regulations: EMC Directive 2014/30/EU Low-Voltage Directive 2014/35/EU... -
Page 4: General Information
2 General Information Storage of the User Manual This user manual enables the safe and efficient use of the P512 Set. It must be kept close at hand and accessible to the use. Reading and Understanding the User Manual Read the user manual carefully, observe the safety information (Chapter 3) and follow the instructions given in this manual before putting the device into service. -
Page 5: Safety
Intended Use The probe set P512 Set is used for testing the conducted immunity of integrated circuits. In accordance with the IEC 62132-4 standard, radio frequency power can be introduced into the circuits via the probe P512. -
Page 6: Staff Requisition
Electromagnetic near fields are generated at the probe due to its function. Therefore, persons with a cardiac device, such as a pacemaker, must not work on or approach the P512 Set during operation. - 6 -... -
Page 7: Scope Of Delivery
12 GHz Power supply unit 12 V Shielded measurement cable SF104/11SMA/11SMA/1000mm System case P512 case Quick guide User manual Important: The scope of delivery may deviate depending on the respective order. Figure 1: P512 Set system case - 7 -... -
Page 8: P512 Probe Set
DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de 5 P512 Probe Set General Description The P512 probe set is used to inject high-frequency currents and voltages into IC pins or to measure RF signals in a 50 Ohm matched circuit. For "Direct Power Injection" (DPI), the P512 is used in conjunction with an RF signal generator and an RF power amplifier. -
Page 9: Design And Function
DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de Design and Function Figure 4: Connections and indicators of the P512 The P512 contains a 50 Ohm RF connection from the RF connector RF (SMA) to the probe tip. in/out The ground connection to the DUT is routed via the ground contacts on the side of the pin contact (ground-signal-ground) and the contact surface of the base. -
Page 10: Contact Detection
DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de Contact Detection The pin contact detection indicates whether there is a galvanic connection between the probe tip and an IC pin/ball. Figure 6: Illustration of the P512 probe with pin contact detection When the pin contact detection button is pressed, a voltage of -5 V is supplied to the probe tip. -
Page 11: Operational Notes
Monitoring of representative signals in the DUT o special test firmware? o visible reaction of the DUT to inputs (reaction test of the DUT) Langer EMV-Technik GmbH accepts no liability for the destruction of the DUT! - 11 -... -
Page 12: Measurement Setup
7 Measurement setup Direct power injection DPI Figure 7: Measuring set-up with ICE1 set (* not included in the scope of delivery of the P512 set ICE1 included in the ICE1 set) Figure 7 shows the measurement setup for DPI measurement with the P512 set. Components from the ICE1 set (IC test environment) from Langer EMV-Technik GmbH are also required for the measurement setup. - Page 13 DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de During the measurement, all pins of the IC can be individually contacted with the P512. The RF power is fed into the IC pin via the coupling network of the P512 and via its pin contact.
- Page 14 DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de Figure 9: DPI measurement set-up with probe P512 - 14 -...
-
Page 15: Measurements Of Rf Signals (P512 Hf-T Set)
GND 25. The P512 probe is connected to a corresponding RF measuring device. Figure 10: Using the P512 set as a 50 Ohm RF probe (* not included in the scope of delivery of ICE1... - Page 16 DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de Other standard oscilloscope probes (not included in the scope of delivery) can be used in the measurement setup with the TH22 (probe holder) supplied in the ICE1 set Figure 11: Equivalent circuit for RF measurements with the P512 probe as a probe in...
-
Page 17: Technical Parameters
DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de 8 Technical Parameters P512 Probe Frequency range Bis 12 GHz Input matching < -10 dB @ 12 GHz see (Figure 12) Insertion loss > -3 dB @ 12 GHz see (Figure 12) Coupling capacity (C 6.8 nF *... - Page 18 DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de Figure 13: Diagram of maximum input power (determined with mismatch at probe tip) - 18 -...
-
Page 19: Housing And Probe Tip Dimensions
DE-01728 Bannewitz LANGER mail@langer-emv.de P512 Set EMV-Technik www.langer-emv.de Housing and probe tip dimensions Figure 14: Specification of housing and tip dimensions - 19 -... -
Page 20: Customer Service
9 Customer service Please contact us if you have any questions, comments or suggestions. You can contact us: Monday – Friday 8:00 Uhr bis 15 Uhr (CET) Contact us at: Address: Langer EMV-Technik GmbH Nöthnitzer Hang 31 01728 Bannewitz Germany Internet: https://www.langer-emv.com/ E-mail: mail@langer-emv.de... -
Page 21: Warranty
This document may not be copied, reproduced or processed, duplicated or distributed using electronic systems, either in whole or in part, without the prior written permission of Langer EMV-Technik GmbH. The management of Langer EMV-Technik GmbH accepts no liability for damage resulting from the use of this printed information.