Related Manuals for Canon imagePRESS Server G250
Summary of Contents for Canon imagePRESS Server G250
- Page 1 Server G250 Installation Procedure PUB No. FT2-8030-000 © CANON INC. 2019...
- Page 2 1. Installation Installation How to Utilize This Installation Procedure.........3 Before Connection..............4 Installation Procedure..............6 Settings After Installation............14...
-
Page 3: How To Utilize This Installation Procedure
1. Installation How to Utilize This Installation Procedure Symbols The frequently-performed operations are described with symbols in this procedure. Screw Tighten Loosen Packaged Item Unused Parts Remove Install Harness (Common for Guides Connector Power Cord and Clamps) Connect Disconnect Connect Disconnect Remove Install... -
Page 4: Before Connection
1. Installation Before Connection Essential Items to Be Performed Before Installation Installing the License • Turn OFF the main power of the host machine, and disconnect the power plug from the outlet. Be sure to take out the license certificate included in the package and obtain the license key in advance. - Page 5 1. Installation Europe x 2 USA x 1 Straight Ethernet Cross Ethernet Cable (3.0 m) Cable (for network connection) Stepped Screw; M4x9 Binding; M4x8 (Screw with TP; M3x6 10x Toothed Washer) Use 6 of them <Others> • Including guides Installation Outline Drawing...
-
Page 6: Installation Procedure
1. Installation Installation Procedure Installing the Open I/F PCB NOTE: Ask the user to keep the removed Face Cover. NOTE: The removed screws will be used in step 8. NOTE: The removed screw will be used in step 8. - Page 7 1. Installation NOTE: NOTE: Ask the user to keep the removed Bypass PCB. Use the screws removed in steps 4, 5 and 6. M3x6 NOTE: The removed screws will be used in step 8. CAUTION: • Uniformly push in the Main Controller PCB 2 with both hands until it stops.
- Page 8 1. Installation CAUTION: CAUTION: • Be sure to turn over the 2 Lock Levers, and push When installing the Box Left Cover, be careful not to in the Main Controller PCB 2. trap cables. • When installing the screws, install the lower screw first and then the upper one.
- Page 9 1. Installation NOTE: NOTE: Hook the Support Plate to the screw (right side) loosened Hook the Support Plate to the screw (left side) loosened in step 1, and install it in the direction of the arrow. in step 1, and install it in the direction of the arrow. M3x6 M3x6 NOTE:...
- Page 10 1. Installation NOTE: Use the 4 screws removed in steps 6. Stepped Screw; M4x9 CAUTION: Be sure to install it in the correction direction. NOTE: Hook the imagePRESS Server to the 2 Stepped Screws (M4x9) tightened in step 5 to install it. Binding;...
- Page 11 1. Installation Cross Ethernet Cable...
- Page 12 1. Installation CAUTION: Use the correct power cord to match the location/area of installation. Make sure not to leave unused power cord at the site. CAUTION: Be sure to use the network cable with Category 5e or higher. In addition, a shielded type (STP cable) is recommended.
- Page 13 1. Installation Turn ON the main power switch of the host machine again. Check that the value of the following service mode is "465". COPIER > OPTION > INT-FACE > CNT-TYPE...
-
Page 14: Settings After Installation
1. Installation Settings After Installation Settings After Installation Setting of the Display Range of 1. Select [Fiery] from the main menu on the host machine's LCD. the Web Browser 1. Select Settings/Registration > [Function Settings] > [Web Access] > [Settings] > [Privacy Policy and Regulations], and set the following items to "ON". - Page 15 1. Installation Check that the items in the General Setup are set, and perform [Save Changes] even if there is no change. 3. Select [Tools] > [Setup]. The setting will not be completed unless [Save Changes] is pressed. 5. Press [Exit Setup] after all settings are completed. 4.
- Page 16 1. Installation 1. Select [Fiery] from the main menu on the host 4. Press [Yes]. machine's LCD. Connecting to the Network Ask the network administrator to connect to the network, 2. Select [Login] to log in as a system administrator. make settings and output the test print.