Door-type dishmachines with ventless & energy recovery (82 pages)
Summary of Contents for Noble C Series
Page 1
NOBLE RACK CONVEYOR DISHMACHINES INSTALLATION, OPERATION, AND SERVICE MANUAL NOBLE C SERIES C-44 C-54 C-66 C-76 C-80 C-90 Noble C Series Manual • 07610-004-40-03-D...
Page 2
REVISION HISTORY Revision Revision Made by Applicable ECNs Details Letter Date 10-25-16 Initial release of manual. Updated manual to new format. 8-18-17 8509 Audited manual and made corrections throughout. Changed C-44/54 Drain Plumbing Assembly. Complete revision of manual. Added electrical requirements for available 380 V machines. Changed steam pressure to 10–30 PSI.
Page 3
NOMENCLATURE C-44CE, C-54CE, C-66CE, C-76CE, C-80CE, C-90CE Electrically-heated rack conveyor machines, available in chemical-sanitizing and hot-water-sanitizing models. C-44CS, C-54CS, C-66CS, C-76CS, C-80CS, C-90CS Steam-heated, hot-water-sanitizing rack conveyor machines. The manufacturer provides technical support for all of the machines detailed in this manual.
OPERATING PARAMETERS SPECIFICATIONS OPERATING SPECIFICATIONS WATER REQUIREMENTS High-temp High-temp Racks per Hour Minimum Wash Temperature (°F/°C) 160/71 Dishes per Hour 5625 Minimum Rinse Temperature (°F/°C) 180/82 Glasses per Hour 8100 Pre-wash Temperature (°F/°C) 110-140/43-60 Flow Pressure (PSI) Low-temp Flow Rate (GPM) 2.57 Racks per Hour Water Line Size (NPT)
ELECTRICAL REQUIREMENTS SPECIFICATIONS All electrical ratings provided in this manual are for reference only. Always refer to machine data plate to get exact electrical information for this machine. All electrical work performed on machines should be done in accordance with applicable local, state, territorial, and national codes. Work should only be performed by qualified electricians and authorized service agents.
Page 25
ELECTRICAL REQUIREMENTS SPECIFICATIONS Local codes may require more stringent protection than what is displayed here and on data plate. Always verify with electrical service NOTICE contractor that circuit protection is adequate and meets all applicable national and local codes. Numbers in this manual are for reference and may change without notice.
Page 26
ELECTRICAL REQUIREMENTS SPECIFICATIONS Local codes may require more stringent protection than what is displayed here and on data plate. Always verify with electrical service NOTICE contractor that circuit protection is adequate and meets all applicable national and local codes. Numbers in this manual are for reference and may change without notice.
INSTRUCTIONS INSTALLATION INSPECTION Before installing machine, check packaging and machine for damage. Damaged packaging indicates possible damage to product. If there is any type of damage to both packaging and machine, DO NOT THROW AWAY PACKAGING. The machine has been inspected at the factory and is expected to arrive in new, undamaged condition.
INSTRUCTIONS INSTALLATION PLUMBING All plumbing connections must adhere to local, state, territorial, and national codes. Installing plumber is responsible for ensuring incoming water lines are flushed of debris before connecting to the machine. Chips and materials from cutting processes can become Plumber MUST flush incoming water line! lodged in solenoid valves and prevent them from opening or closing.
INSTRUCTIONS INSTALLATION STEAM LINE Steam models come with lines to connect the source steam. Connect all steam lines to machine as applicable codes provide. See machine data plate for information on CONNECTIONS steam flow pressure. Click on instructions icon for Steam Booster manual. ELECTRICAL All electrical connections must be made in accordance with applicable portions of local, state, territorial, and national codes.
INSTRUCTIONS INSTALLATION MOTOR On 3-Phase machines only, correct pump motor rotation must be verified before machine is operated. Failure to do so can result in damage to machine and components. ROTATION 1. Follow Power Up section. CAUTION CAUTION! On 3-Phase machines only, correct pump Motor Fan motor rotation...
INSTRUCTIONS INSTALLATION CHEMICAL FEEDER This machine does not come with an integrated chemical supply/feeder system. For the machine to operate correctly, connect it to a third-party chemical dispenser (see EQUIPMENT Connection Points section) that meets requirements of NSF Standard 29. Contact a chemical supplier about connecting a dispenser to machine.
INSTRUCTIONS INSTALLATION CONNECTION POINTS Incoming Water Rinse-aid Rinse-aid tube connection shown on right. GRND Terminals marked "CVS" provide a voltage signal whenever drive motor is operating. Terminals marked "DET" provide a voltage signal whenever wash motor is operating. There is no dedicated connection for a rinse-aid dispenser.
CURTAINS INSTALLATION Decals mark curtain locations inside machine, starting at load end and ending at unload end. Illustrations below (Left- to-Right machines shown, Right-to-Left are mirrored) indicate curtain size to be placed on curtain hooks provided. If any curtain components are missing, they MUST be obtained and installed before operation. CE &...
OPERATING INSTRUCTIONS OPERATION PREPARATION Before operating, verify: 1. Drain handle is turned to “CLOSE” position. OPEN CLOSE 2. Strainers and pawl bar are installed and secure. 3. Actuator switches move with relative freedom and do not bind. 4. Curtains are installed correctly. POWER UP 1.
OPERATING INSTRUCTIONS OPERATION FIRST RACK The first rack will typically reduce temperature of wash tank and might need to be run through again. This might be necessary any time machine has not been operated for an extended period of time; although this is dependent on type of ware being used, its temperature, and ambient temperature of kitchen area.
OPERATING INSTRUCTIONS OPERATION SHUTDOWN Press OFF button on front of machine. Move drain handle to OPEN position. If machine is equipped with a booster, shut it down according to third-party manufacturer’s instructions. & CLEANING Clean machine at least once every 24 hours or at end of day. Cleaning removes soil and debris that might become trapped in nozzles or deposited onto ware.
Page 37
OPERATING INSTRUCTIONS OPERATION SHUTDOWN 5. As needed, clean wash and rinse arms: a. Remove wash arm manifolds. & CLEANING For machines with pre-wash sections, also remove and clean the pre-wash arm. b. Remove end-caps from arms and manifolds. c. Clean nozzles with a brush. Also clean rinse assembly nozzles. d.
OPERATING INSTRUCTIONS OPERATION DELIMING 1. Disconnect/turn off chemical feeder equipment. 2. Turn machine on. GRND 3. Add deliming solution according to chemical supplier’s instructions. 4. Close door. 5. Flip AUTOMATIC/DELIME switch to DELIME. 6. Run machine period of time recommended by chemical supplier. 7.
PREVENTATIVE MAINTENANCE MAINTENANCE PREVENTATIVE The manufacturer highly recommends that only qualified service personnel perform any maintenance and repairs not specifically discussed in this manual. MAINTENANCE WARNING! Unqualified personnel performing maintenance on the machine may void the warranty, lead to larger problems, or cause harm to operator. WARNING Following operating and cleaning instructions in this manual will ensure the machine operates efficiently.
PREVENTATIVE MAINTENANCE LUBRICANTS MAINTENANCE WORM GEAR REDUCERS DRIVE GEAR The maintenance procedures detailed here are manufacturer’s instructions for the brand of gear reducer that is installed on the machines covered in this manual. REDUCER For special applications that involve severe ambient experience, recommends the use of Mobil SHC temperature extremes or a seasonal oil requirement, synthetic lubricants.
Page 41
PREVENTATIVE MAINTENANCE MAINTENANCE DRIVE GEAR after a short period of operation and adjusted, if necessary. When changing double- reduction models, each housing should be drained and filled independently, even though REDUCER there could be a common level. LUBRICATION Initial oil change - The new oil in a speed reducer should be changed at the end of 250 hours of operation.
TROUBLESHOOTING TROUBLESHOOTING WARNING: Inspection, testing, and repair of electrical equipment should only be performed by a qualified service technician. Many of the tests require that the machine have power to it and live electrical components be exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE. WARNING OBSERVATION POSSIBLE CAUSE...
Page 43
TROUBLESHOOTING TROUBLESHOOTING WARNING: Inspection, testing, and repair of electrical equipment should only be performed by a qualified service technician. Many of the tests require that the machine have power to it and live electrical components be exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE. WARNING OBSERVATION POSSIBLE CAUSE...
C-44/54 CONTROL BOX PARTS GRND ITEM DESCRIPTION PART NUMBER Electrical Box 05700-041-88-43 Terminal Block 05940-011-48-27 Rinse Thermometer, 96” Lead 06685-111-68-48 09905-002-97-62 Rinse Decal, 180 °F Star Washer, External Tooth, 10-24 05311-273-02-00 Screw, 10-32 x 3/4” Long Phillips Trusshead 05305-011-62-17 Decal, Gauge 09905-021-72-29 Wash, Thermometer, 48”...
Page 45
C-44/54 CONTROL BOX PARTS ITEM DESCRIPTION PART NUMBER Switch, ON/FILL - OFF/DRAIN 05930-301-46-00 Motor Contactor 05945-111-68-38 Heater Contactor (CE Only) 05945-002-24-70 Overload See Motor Overloads page. Overload See Motor Overloads page. Control Relay 05945-111-35-19 Control Relay 05945-111-72-51 Screw, 6-32 x 3/8” Long Round Phillipshead 05305-002-25-91 Fuse (460 V Only) 05920-011-72-88...
C-66/76/80/90 CONTROL BOX PARTS GRND ITEM DESCRIPTION PART NUMBER Electrical Box 05700-041-88-50 Decal, L1, L2, L3 09905-101-12-66 Terminal Block 05940-011-48-27 Terminal Board 05940-021-89-41 Decal, Gauge 09905-021-72-30 Light, Amber (CE Only) 05945-111-44-44 Wire Lug, 2 AWG to 14 AWG 05940-200-76-00 Light, Red 05945-111-44-45 Din Rail 05700-021-72-75...
Page 47
C-66/76/80/90 CONTROL BOX PARTS ITEM DESCRIPTION PART NUMBER Terminal Board 05940-002-78-97 Motor Contactor 05945-111-68-38 Circuit Breaker (208-230 Volt, 60 Hz Models Only) 05925-011-68-34 Overload See Motor Overloads page. Switch, ON/FILL - OFF/DRAIN 05930-301-46-00 Overload See Motor Overloads page. Overload See Motor Overloads page. Heater Contactor (CE Only) 05700-002-24-70 Control Relay...
HEATER BOX PARTS ITEM DESCRIPTION PART NUMBER Heater Box Cover 05700-002-02-04 Heater Box 05700-002-98-38 05930-011-49-43 Thermostat, High Limit Fitting, 1/4”, Imperial Brass 05310-924-02-05 Heater See next page. Terminal Board 05940-002-78-97 Thermostat, Wash Regulating (CE Series) 05930-003-13-65 Kit, Wash Regulating Thermostat (CS Series) 06401-003-18-21 07610-004-40-03-D...
Page 51
HEATER BOX PARTS ITEM DESCRIPTION PART NUMBER 5/16-18 Hex Nut 05310-275-01-00 Heater See table below. Heater Gasket 05330-200-02-70 5/16" Lockwasher 05311-275-01-00 HEATERS VOLTS PHASE PART NUMBER 04540-121-79-30 04540-121-79-31 04540-121-79-30 04540-121-79-31 04540-121-79-32 *Steam models do not use electric heaters. When replacing a heater, it is HIGHLY recommended that the heater gasket be changed as well. Once NOTICE installed, gaskets become compressed and are subjected to extreme temperature changes.
Page 52
HEATER BOX PARTS HEATER SYSTEM TROUBLESHOOTING The wash tank heater system is electrically-connected in the circuit and is dependent upon the machine being properly filled with water and maintaining a safe water level. The system consists of two thermostats (mounted in the heater box behind the dress panel), a float switch (mounted in the wash tank), the heater relay (mounted in control box), and the heater which is activated by the thermostats.
Page 53
HEATER BOX PARTS HEATER PROTECTION AND AUTOMATIC FILL (FOR UNITS EQUIPPED WITH AUTOMATIC FILL) This control is activated when the power switch is turned “ON.” The primary function is to automatically energize the wash tank heating circuit. It will also cut-off the wash tank heating circuit should the water be accidentally drained from the machine with the power switch still “ON.”...
PLUMBING OPTIONS PARTS SHOCK ABSORBER (WATER ARRESTOR) OPTION Water Arrestor, 1/2” 06685-100-05-00 Tee, 3/4” x 3/4” x 1/2” 04730-211-06-00 Nipple, 3/4”, Close, Brass 04730-207-34-00 WATER TREATMENT OPTION Scaltrol System Replacement Cartridge 04730-003-05-76 (inspect at least every 6 months) RSC-100 PRESSURE REGULATING VALVE OPTION (WITH SHOCK ABSORBER) Water Arrestor, 1/2”...
SOLENOID VALVE & VACUUM BREAKER PARTS Screw Data Plate Cap Screw Coil & Housing Data Plate Valve Bonnet Spring Plunger Cap Retainer O-ring Diaphragm Retainer O-ring Diaphragm Plunger Components of Repair Kit Screen Retainer Body Mesh Screen Valve Body Solenoid Valve Plunger Kit Vacuum Breaker Repair Kit Includes plunger and spring 06401-003-06-23...
STEAM COIL PARTS Complete Steam Coil Assembly 05700-002-11-78 ITEM DESCRIPTION PART NUMBER Stand "D" 05700-002-74-85 Steam Coil 05700-002-84-03 Stand "C" 05700-002-74-84 Coil Gasket 05700-001-17-86 Flat Washer 05700-001-17-87 Coil Nut 05310-011-17-85 Stand "B" 05700-002-74-83 The Coil Gasket should be replaced any time the Steam Coil is replaced or removed for an extended NOTICE period of time.
STEAM PLUMBING, L-R PARTS INLET OUTLET ITEM DESCRIPTION PART NUMBER Reducer, 3/4” to 1/2”, Black Iron 04730-911-02-34 Union, 3/4”, Black Iron 04730-912-01-00 Nipple, Close, 3/4”, Black Iron 04730-907-01-00 Valve, Steam Solenoid, 3/4”, 120 V 04820-011-87-39 Elbow, 90-degree, 3/4”, Black Iron 04730-906-10-34 Elbow, Street, 90-degree, 3/4”, Black Iron 04730-011-87-37...
STEAM PLUMBING, R-L PARTS INLET OUTLET ITEM DESCRIPTION PART NUMBER Reducer, 3/4” to 1/2”, Black Iron 04730-911-02-34 Union, 3/4”, Black Iron 04730-912-01-00 Nipple, Close, 3/4”, Black Iron 04730-907-01-00 Valve, Steam Solenoid, 3/4”, 120 V 04820-011-87-39 Elbow, 90-degree, 3/4”, Black Iron 04730-906-10-34 Elbow, Street, 90-degree, 3/4”, Black Iron 04730-011-87-37...
C-66/76/80/90 DRAIN PLUMBING, R-L PARTS ITEM DESCRIPTION PART NUMBER Elbow, 1 1/2”, Street Brass 04730-206-32-00 Ball Valve, 1 1/2” 04820-011-71-46 Adapter, Male to Female, 1 1/2” 04730-401-25-01 Tube, Copper, 1 1/2” x 1 7/8” (All Models) See note below. Tee, Brass, 1 1/2” 04730-011-69-93 Nipple, Close Brass, 1 1/2”...
DRAIN WATER TEMPERING SYSTEM PARTS Complete Drain Water Tempering System 05700-002-44-07 To Cold Water Supply To Machine Drain To Facility Drain From the existing drain, attach the two additional Tees (Item 7) using the 1 1/2” Close Brass Nipples (Item 8). Tighten the Reducers (Items 6 and 9) into the Tees as shown above.
MOTOR PARTS ITEM DESCRIPTION PART NUMBER Motor See table on the next page. Key, 3/16” x 1” 05700-011-89-17 Pump Plate 05700-021-71-83 Pump Seal 05330-011-71-98 Impeller (C-44/54) 05700-031-67-45 05700-031-71-78 Impeller (C-66/76/80/90) Impeller Washer 05700-011-71-95 Bolt, Hex Head 1/4-20 x 3/4” 05305-004-42-64 Upper Support Bracket 05700-021-73-68 Nut, 1/4-20 Serrated...
Page 67
MOTOR PARTS WASH MOTORS Volts Phase Motor Part Number Complete Kit Part Number 200-440 06105-121-81-34 06401-003-09-96 208-230 06105-021-70-57 06401-003-09-97 208-230 06105-004-69-12 06401-003-09-98 06105-121-81-34 06401-003-09-96 06105-004-69-12 06401-003-09-98 06105-002-48-31 06401-003-09-99 PRE-WASH MOTORS C-66/76 Volts Phase Motor Part Number Complete Kit Part Number 208-230 06105-121-70-56 06401-003-10-38...
FINAL RINSE PARTS ITEM DESCRIPTION PART NUMBER Rinse Arm Support Bracket 05700-002-06-24 Gasket, Final Rinse Manifold 05330-111-42-81 Rinse Arm 05700-002-02-18 End-cap 05700-002-02-19 Rinse Nozzle 04730-003-59-63 Final Rinse Manifold 05700-002-97-41 Rinse Pan Strainer 05700-041-85-09 Locknut, 1/4-20 with Nylon Insert 05310-374-01-00 Rinse Drain Control Plate 05700-011-68-70 Rinse Drain Overflow Plate 05700-002-53-62...
DOORS PARTS ITEM DESCRIPTION PART NUMBER Door 05700-003-13-47 Pre-wash Door, Left-to-Right 05700-003-13-42 05700-003-13-40 Pre-wash Door, Right-to-Left Screw, 8-32 x 1/4” 05305-172-09-00 Door Switch Magnet 05700-111-51-68 Door Guide 05700-111-70-92 Bracket, Right Door Stop 05700-002-96-33 Bracket, Left Door Stop 05700-002-96-32 Locknut, 10-24 Hex with Nylon Insert 05310-373-01-00 Bracket, Pre-wash Door Stop 05700-002-05-46...
DRIVE ASSEMBLY PARTS Complete Drive Assembly 05700-003-60-69 ASSEMBLED VIEW Part numbers 33 and 34 are assembled in this hole for all low-temperature (chemical-sanitizing) machines. Part numbers 33 and 34 are assembled in this hole for all high-temperature (hot-water-sanitizing) machines. (This is the hole in the farthest clockwise position.) ITEM DESCRIPTION PART NUMBER...
Page 74
DRIVE ASSEMBLY PARTS ITEM DESCRIPTION PART NUMBER Collar, Shaft Conveyor Drive 05700-011-89-18 Spring, Adjuster 05315-011-71-90 Nut, Hex, 3/8-16 05310-276-01-00 Set Screw, 5/16-18 x 1/4" 05305-002-98-39 Bolt, 3/8-16 x 3/4” 05306-011-71-60 Bolt, 1/4-20 x 1/4" 05305-274-22-00 Washer, 1/4-20 05311-174-01-00 Locknut, 1/4-20 Hex with Nylon Insert 05310-374-01-00 Spring, Drive 05315-011-83-51...
PAWL BAR ROLLER BRACKET PARTS ITEM DESCRIPTION PART NUMBER Pawl Bar Bracket (No Tabs) 05700-031-92-36 Pawl Bar Roller Replacement Kit 06401-003-11-80 Pawl Bar Bracket (Tabs) 05700-031-84-68 Top Guide Block 05700-011-69-49 06401-003-10-15 Guide Block Replacement Kit Pawl Bar Gutter Gasket 05330-011-68-55 Bottom Guide Block 05700-011-69-50 Pawl Bar Gutter Replacement Kit...
C-44/66 PAWL BARS PARTS Complete C-44 Pawl Bar Assembly with Hardware 06401-131-81-00 Complete C-66 Pawl Bar Assembly with Hardware 06401-141-74-64 ITEM DESCRIPTION PART NUMBER 12 on C-44 Pawl Bar Dog Casting 09515-021-69-00 18 on C-66 24 on C-44 Pawl Bar Spacer 05700-011-71-45 36 on C-66 Pawl Bar (C-44)
C-80 PAWL BAR PARTS Complete C-80 Pawl Bar Assembly with Hardware, L-R 06401-131-81-06 Complete C-80 Pawl Bar Assembly with Hardware, R-L 06401-241-81-06 ITEM DESCRIPTION PART NUMBER Pawl Bar Dog Casting 09515-021-69-00 Bolt, 3/8-16 x 1-3/4” Long 05306-011-36-94 Pawl Bar (L-R) 05700-031-74-19 05700-041-82-01 Pawl Bar (R-L)
C-44 RACK RAILS PARTS ITEM DESCRIPTION PART NUMBER Front Rack Rail 05700-031-69-48 Rear Rack Rail (Not Shown) 05700-031-67-59 Actuator Switch 05700-021-72-39 Actuator Switch Replacement Kit 06401-003-10-14 Bolt, Hex Head 1/4-20 x 3/4" 05305-004-42-64 Pawl Bar Spacer 05700-011-71-44 Locknut, 1/4-20 Hex with Nylon Insert 05310-374-01-00 Kit contains the switch, two spacers, and hardware.
C-66 RACK RAILS PARTS Left-to-Right Right-to-Left ITEM DESCRIPTION PART NUMBER Large Actuator Switch, L-R 05700-021-76-97 Large Actuator Switch Replacement Kit, L-R 06401-003-10-99 Large Actuator Switch, R-L 05700-002-91-09 06401-003-10-86 Large Actuator Switch Replacement Kit, R-L 8 per rail Bolt, Hex Head 1/4-20 x 3/4" 05305-004-42-64 8 per rail Locknut, 1/4-20 Hex with Nylon Insert...
C-80 RACK RAILS PARTS Left-to-Right Right-to-Left ITEM DESCRIPTION PART NUMBER Large Actuator Switch, L-R 05700-021-77-01 Large Actuator Switch Replacement Kit, L-R 06401-003-10-83 Large Actuator Switch, R-L 05700-002-91-10 06401-003-10-85 Large Actuator Switch Replacement Kit, R-L 8 per rail Bolt, Hex Head 1/4-20 x 3/4" 05305-004-42-64 8 per rail Locknut, 1/4-20 Hex with Nylon Insert...
STRAINERS PARTS Parts are not shown to scale with relation to each other. ITEM DESCRIPTION PART NUMBER Drain Guard Strainer 05700-002-09-15 Screen Strainer with Handle 05700-002-09-04 Wash Intake Strainer 05700-001-22-23 Wash Strainer Separator 05700-002-48-43 Tub Strainer 05700-002-03-21 07610-004-40-03-D...
RINSE FILL OPTION PARTS Complete Rinse Fill Motor Assembly 05700-002-40-25 Complete Rinse Fill Motor Assembly (C-66 L-R Only) 05700-002-48-22 ITEM DESCRIPTION PART NUMBER Motor 06105-002-72-71 Bracket, Pump Mounting 05700-003-17-56 Clamp, Hose 5 5/8” to 6” 04730-011-34-90 Reducer Bushing, 1 1/4” to 1” 04730-002-73-62 Reducer Bushing 1”...
FLOAT SWITCH/SCRAP BASKET PARTS Parts are not shown to scale with relation to each other. ITEM DESCRIPTION PART NUMBER Float Switch Support Bracket Kit* 06401-003-11-77 Float Switch Cover 05700-021-75-71 Wash Tank Float Switch Kit* 06401-003-11-75 06401-003-11-76 Pre-wash Tank Float Switch Kit* Scrap Basket Lid 05700-002-56-55 Scrap Basket Assembly...
CURTAINS/CONVEYOR SWITCH PARTS Parts are not shown to scale with relation to each other. 24.5 ITEM DESCRIPTION PART NUMBER Curtain, XL, 24 1/2” x 20 1/2” 08415-002-47-37 Curtain, L, 21” x 20 1/2” 08415-131-73-45 Curtain, S, 12” x 20 1/2” 08415-131-73-44 Decal, XL Curtain 09905-004-38-49...
MISCELLANEOUS PARTS PARTS Parts are not shown to scale with relation to each other. ITEM DESCRIPTION PART NUMBER Vent Cowl 05700-041-86-94 Vent Cowl Cover 05700-011-74-67 Vent Cowl Cover Replacement Kit* 06401-003-10-16 Gasket, Top Vent Cowl 05330-031-83-47 Gasket, Side Vent Cowl 05330-031-83-48 Vent Scoop Option 05700-002-04-08...
Page 88
MISCELLANEOUS PARTS PARTS Parts are not shown to scale with relation to each other. ITEM DESCRIPTION PART NUMBER Plate, Left Water Directional 05700-021-79-27 Plate, Right Water Directional 05700-021-79-23 Run-off Sheet 05700-021-71-39 Splash Shield 05700-031-85-16 Hole Direction Plate Kit* 06401-003-10-00 Rinse Drain Plate Gasket 05330-011-72-27 Pipe Clamp 05700-000-35-05...