Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kew Labs UTS-2
Summary of Contents for Kew Labs UTS-2
- Page 1 UTS-2 User Instructions Installation Guide...
- Page 2 IN THE BOX UTS-2 charger LED alignment tool User instructions Sticker selection Cable management clips Screws Country plug adapters (UK, EU, AUS) Power adaptor USB C Cable UTS-2 User Instructions Installation Guide 1 of 14...
-
Page 3: Check Before Installation
CHECK BEFORE INSTALLATION If you have a phone case please ensure it is flat and does not contain any metal, center magnets, card holders, pop sockets or kickstands. Ensure the surface under your table is flat. Prepare a pencil and screwdriver if needed. Check installation area is within 1.5m (4’... - Page 4 STAGE 1 - SURFACE THICKNESS PREPERATION 1. Check the thickness of the surface is correct before your installation. UTS-2 can only be installed in non-metallic surfaces between 8-12mm (0.31"–0.5"). Thicker surfaces will need to be thinned through routing to ensure universal compatibility with Qi wireless charging devices.
- Page 5 4. Choose between screw or tape installation. Tape or screw the charger into position making sure the charger still reaches the power point (screws may be easier to remove). 5. Attach the power cord and use the cable management clips if required. 4 of 14...
- Page 6 STAGE 2 - PHONE CALIBRATION Ensure UTS-2 is attached to the surface to the correct thickness and flush to the surface underside. Follow the instructions on the alignment tool until the LED flashing sequence shows. 5 of 14...
- Page 7 TO DISABLE OR ENABLE BUZZER UTS-2 has a confirmation buzzer that can be turned on and off depending on preference. Changing the buzzer sound: Hold button on the underside of charger for 2-4 seconds until you hear the unit beep.
-
Page 8: General Use Instructions
1. Place your phone face up aligning the center of your phone to the center of the sticker. 2. The UTS-2 will make an audio confirmation beep to indicate the accuracy of your phone positioning. A beep is confirmation that your phone has been placed in an optimal position for charging and fast charging. -
Page 9: Troubleshooting And Faqs
Check your charger is stuck flush to the underside of the surface. Why has my phone stopped charging? The UTS-2 is designed to recognise and react to temperature changes within your phone which can occur after extra long charging periods of 3 hours or more. In these instances, the charger may enter a standby mode to allow your device to cool if required by your phone until the device requests more power. - Page 10 Charging speeds may also slow at ≥80% in IOS models due to Apple software requirements designed to limit battery deterioration during wireless charging. The UTS-2 recognises IOS charging signals and corresponds by adapting charging speeds until your device requests more power. Please try turning OFF ‘Optimised Battery Charging’ in your ‘Settings’.
-
Page 11: Specifications
SPECIFICATIONS Fast Charging Speeds Qi enabled Apple 7.5W / Samsung 9W Fast Charge. Charging Distance 8mm ~ 12mm (0.31” ~ 0.5”) Normal Charging Qi enabled Google , Huawei , Sony , Nokia , Speed LG , Xiaomi 5W Charge. Charges Through All non-metallic surfaces wood, plastic, granite, quartz, marble glass. -
Page 12: System Fault
System Fault can be used again after removing cause of occurrence, turning power off and on. BUZZER INDICATION Status Buzzer Power Transfer Start Beep Beep: Buzzer Off Press UTS-2 button Beep-Beep: Buzzer On (at Power Transfer Start) 11 of 14... -
Page 13: Warranty
WARRANTY Kew Labs warrants to the purchaser that your product shall be free from defects in material and workmanship for the length of time, identified on your product package and/or at www.kewlabstech.com under the warranty specification for your product, from the date of purchase. This warranty is non transferable and is limited to original purchaser and the country it was purchased in. -
Page 14: Safety Instructions
SAFETY INSTRUCTIONS • Avoid contact with water and do not submerge. • Avoid extreme temperatures. • Avoid dropping. • Use original or certified cables. • Do not clean with corrosive substances or oils. • Do not disassemble. • This product is in compliance with the radio interference. requirements of the European Community. - Page 15 This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna.
Need help?
Do you have a question about the UTS-2 and is the answer not in the manual?
Questions and answers