Table of Contents
Advertisement
Quick Links
USB3-FRM12
User Manual
Version 1.1
ⓒ 2005 DAQ SYSTEM Co., Ltd. All rights reserved.
Microsoft® is a registered trademark; Windows®, Windows NT®, Windows XP®, Windows 7®, Windows 8®, Windows 10®
All other trademarks or intellectual property mentioned herein belongs to their respective owners.
Information furnished by DAQ SYSTEM is believed to be accurate and reliable, However, no responsibility is assumed by DAQ SYSTEM for its use, nor
for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under
any patent or copyrights of DAQ SYSTEM.
The information in this document is subject to change without notice and no part of this document may be copied or reproduced without the prior
written consent.
Advertisement
Table of Contents
Related Manuals for DAQ USB3-FRM12
Summary of Contents for DAQ USB3-FRM12
- Page 1 All other trademarks or intellectual property mentioned herein belongs to their respective owners. Information furnished by DAQ SYSTEM is believed to be accurate and reliable, However, no responsibility is assumed by DAQ SYSTEM for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or copyrights of DAQ SYSTEM.
-
Page 2: Table Of Contents
USB3-FRM12 User’s Manual Contents 1. Introduction -------------------------------------------------------------------------- 1-1 Product Features ------------------------------------------------------------------------ 1-2 Product Applications ------------------------------------------------------------------------ 2. USB3-FRM12 Board Function 2-1 Block Diagram ------------------------------------------------------------------------ 2-2 DVI(Digital Video Interface) ------------------------------------------------------------- 3. USB3-FRM12 Board Description 3-1 USB3-FRM12 Board Layout ----------------------------------------------------------------- 3-2 Device Features... - Page 3 USB3-FRM12 User’s Manual 5. Sample Program --------------------------------------------------------------------- Appendix A-1 Board Size ---------------------------------------------------------------------- A-2 Repair Regulations ---------------------------------------------------------------------- References ------------------------------------------------------------------------...
-
Page 4: Introduction
USB3-FRM12 User’s Manual 1. Introduction The USB3-FRM12 is a Frame Grabber capture card with a single link DVI input. This card transfers data captured from video capture devices - DVI cameras, other LCD monitor inputs (using a splitter), game consoles, etc. - to a PC via a USB 3.0 bus (5Gbps). The operation of the board is controlled by the program API. -
Page 5: Product Features
USB3-FRM12 User’s Manual 1-1 Product Features Items Description Remark Hardware PC Interface USB 3.0 B-Type Operation Power +12VDC/650mA External 12V DC Power (A6-Type : 5.5x2.1mm) Video Interface DVI (Digital Video Interface) Feature Interface On-board Memory 256MB (DDR3) Communication UART(Data bit 8, 1 start, 1 stop, No... -
Page 6: Block Diagram
2. USB3-FRM12 Board Function 2-1 Block Diagram As shown in the figure below, in the case of USB3-FRM12, FPGA Core Logic is in charge of overall control. Its main function is to receive Image Frame Data through the DVI connector, write it to DDR#1, DDR#2, and transmit it to the PC upon request. - Page 7 USB3-FRM12 User’s Manual 2-2 DVI (Digital Visual Interface) DVI (Digital Visual Interface) is divided into DVI-D (Digital Only), DVI-A (Analog Only), and DVI-I (Integrated Digital & Analog) methods. The PCIe-FRM14 board supports DVI-I type DVI, so it is compatible with the existing analog type methods. Also, HDMI (High Definition Multimedia Interface) that uses the same format of digital image data can be used together by using the DVI to HDMI gender.
- Page 8 [Refer to 4.3.2 for DVI connector and signal line] In the case of USB3-FRM12, it can process 300MB/sec video data, so 60 fps (frame per second) is possible at 800 x 600, 1024 x 768 resolution, and 30 fps is possible at 1280 x 960 ~...
- Page 9 USB3-FRM12 User’s Manual Control signal line consists of LVAL (Line Valid), FVAL (Frame Valid), DVAL (Data Valid) and clock, and transmits the valid horizontal and vertical resolution and data of the image to be transmitted according to the clock. TMDS Receiver such as monitor and TMDS Transmitter such as graphic card have EDID (Extended Display Identification Data) standard for data communication between the output of the source device and the display.
-
Page 10: Usb3-Frm12 Board Description
USB3-FRM12 User’s Manual 3. USB3-FRM12 Board Description Each important board function is briefly described. For detailed function information, please refer to the parts specification. 3-1 USB3-FRM12 Board Layout USB3-FRM12 Board REF1 REF2 USB3-FRM12 Rev. A [Figure 3-1. USB3-FRM12 Layout] There are a total of six LEDs on the board, the most important of which is D5, and the description of each is as follows. -
Page 11: Device Features
USB3-FRM12 User’s Manual 3-2 Device Features (1) FPGA : U7 All of the board functions are controlled by the Logic program of the FPGA. (2) DVI Receiver : U6 Receives DVI Data and transmits it to FPGA. (3) Regulator : U1, U2, U12 It supplies the power used by the board. -
Page 12: Connector Pin Out
USB3-FRM12 User’s Manual 3-3 Connector Pin-out This section describes the connectors and jumpers used in USB3-FRM12. The main connectors are CN1 for USB 3.0 connection and CN2 connector for DVI connector for DVI connection. 3-3-1 CN1 Connector The PIN of the USB3.0 standard powered-B type connector on the board is shown in [Figure 3-2] when viewed from the front where the cable is connected. -
Page 13: Cn2 Connector
[Figure 3-3] below shows the pin map of the CN2 connector of the board. All pin specifications are input/output based on the DVI standard, so please refer to the DVI standard document for details. [Figure 3-3. USB3-FRM12 CN2 Connector Pin-out] [Table 2. CN2 DVI Connector] Pin #... -
Page 14: J1 Connector
USB3-FRM12 User’s Manual TMDS Data0/5 Shield TMDS Data5- Digital Red- (Link 2) TMDS Data5+ Digital Red+ (Link 2) TMDS Clock Shield TMDS Clock+ Digital Clock+ (Link 1 & 2) TMDS Clock- Digital Clock- (Link 1 & 2) Analog Red Analog Red (Disabled) -
Page 15: J5 Connector
Do not use when operating the board normally. 3-3-8 J9 Switch The USB3-FRM12 board is designed so that up to 4 USB3-FRM12 boards can be used simultaneously in one system (PC). Each board classification can be set through the 4-pin DIP switch in the board. -
Page 16: Sw1
USB3-FRM12 User’s Manual 3-3-9 SW1 This is a 3.3V power reset switch. SW_RST 3.3V [Figure 3-7. SW1 switch] 3-3-10 SW2 5V On/Off Switch. From USB5V [Figure 3-8. switch SW2]... -
Page 17: Installation
USB3-FRM12 User’s Manual 4. Installation 4-1 Product Contents Before installing the board, check that the contents of the package are intact. 1. USB3-FRM12 Board 2. USB(A-B) Cable 3. CD (Driver/Manual/API/Sample Source etc.) 4-2 Installation Process To install the board in the PC, follow the procedure below. In the case of USB, there is no special consideration for board installation as it is a Hot Plug and Plug &... - Page 18 USB3-FRM12 User’s Manual The item “USB 3.0 Root Hub” should be shown in the “Device Manager” window as shown in [Figure 3-1]. After checking the PC environmental conditions for USB3-FRM12, do the following steps to install the board (1) Install the USB3-FRM12 board into your system.
- Page 19 USB3-FRM12 User’s Manual If new hardware is found, Wizard will ask you to install the corresponding driver, For installation of the driver, select item “Install from a list or specific location(Advanced)” and click “Next” as in the [Figure 4-3]. [Figure 4-3. Specify the driver folder] Select “Search for the best driver in these locations”.
- Page 20 USB3-FRM12 User’s Manual [Figure 4-4. Warning window] When you across a window’s warning message regarding to the compatibility problem as shown the [Figure 4-4] during the installation process, just click “Continue” button and go on the installation.
- Page 21 USB3-FRM12 User’s Manual If the installation is completely finished, a completion window message shall be shown as in [Figure 4-5]. Click “Finish”. [Figure 4-5. “Completion” message window]...
- Page 22 Device V1.0” in the “Device Manager” window as shown in [Figure 4-6]. [Figure 4-6. “Device Manager” window] If you can see the “DAQ system USB3.0 Frame 12 Device V1.0” at the Universal Serial Bus controllers, the driver installation is to have been over. (Check the red circle)
-
Page 23: Sample Program
USB3-FRM12 User’s Manual 5. Sample Program In the Exe folder of the CDROM provided with the board, a sample program “FrameTest.exe” is provided for easy use of the board. By displaying Frame Data as hexadecimal values, it is stored in memory or hard disk so that developers can utilize the frame data needed. - Page 24 All files specified above are included on the supplied CDROM. In order to run the sample program normally, the API DLL (USB3-FRM12.DLL) must be in the folder of the executable file or in the Windows system folder or the folder specified by the Path environment variable.
- Page 25 USB3-FRM12 User’s Manual (10) “Skip” toggle When check this box, it displays a stop image. (11) “Full screen” toggle When check this box, it displays a full screen. (12) “Rate: Frame” It shows a frame number per second. (13) “Use Multi Board” toggle It is performed only once after power is applied to the board in case of the multi USB3.0...
-
Page 26: Appendix
USB3-FRM12 User’s Manual Appendix A-1 Board Size The external dimensions of the board are as follows. (For detailed dimensions, please ask the person in charge.) 6.35 51.9 < Top View > 17.5 < Right Side View >... -
Page 27: Repair Regulations
Thank you for purchasing a DAQ SYSTEM product. Please refer to the following regarding Customer Service regulated by DAQ SYSTEM. (1) Read the user manual before using the DAQ SYSTEM product and follow the instructions.. (2) When returning the product to be repaired, please write down the symptoms of the failure and send it to the head office. -
Page 28: References
1. USB 3.0 System Architecture -- Don Anderson, USB SIG(www.usb.org) 2. Universal Serial Bus Specification -- Compaq/Intel/Microsoft/NEC, MindShare Inc. (Addison Wesley) 3. AN201 How to build application using API -- DAQ system 4. AN342 USB3-FRM12 API ver1.0 -- DAQ system... - Page 29 USB3-FRM12 User’s Manual MEMO Contact Point Web sit : https://www.daqsystem.com Email : postmaster@daqsystem.com...