Table of Contents
Advertisement
Available languages
Available languages
Display
When power is first supplied to the microwave oven, "12 Hr" will
appear in the display. User can press TIMER/Clock button or
+/- button to toggle between 12 Hr or 24 Hr within 10 seconds.
Press START button to confirm. If the "12:00" appears in the
display at any other time, a power failure has occurred. Reset
the clock if needed. See the "Clock" section.
Standby mode
When no functions are being used, the microwave oven will
switch to Standby mode.
After function selection, press the STOP/UNLOCK key to exit the
function selection. If you again press the STOP/UNLOCK key it
will be a invalid, as cooking mode is not activated.
When cooking mode is activated and the user presses the
STOP/UNLOCK button, the STOP/UNLOCK functions will be
triggered at the same time. Press the STOP/UNLOCK button
again to cancel the function and return to Standby mode.
START
The START button begins any function. If non-sensor cooking
is interrupted by opening the door, pressing START button will
resume the cycle.
NOTE: To avoid unintentional operation of the microwave oven,
a cooking function cannot be started if the microwave oven door
has been closed for about 1 minute. The word "door" will appear
in the display until the door is opened and closed.
Quick Start/Add 30 seconds
In standby mode, pressing START automatically starts the
microwave oven at 100% power for 30 seconds and adds
30 seconds of cook time, with each additional touch of the
control. Time may be added to any manual cooking cycle in
30 second increments, at the moment power level, by pressing
START button during cooking.
STOP/UNLOCK
The STOP/UNLOCK button clears any incorrect command and
cancels any program during cooking. Press the STOP/UNLOCK
button to stop the cycle. It will not erase the time of day.
The microwave oven will also turn off when the door is opened.
Close the door and press START to resume the cycle.
To use Non-Sensor Menu
(Popcorn, Potato)
1. Place food on the turntable and close the door.
2. Touch desired menu control. The first programmed amount
will appear in the display. Touch control keypad repeatedly or
touch number keypads to change quantity.
3. Touch START. When the cycle ends, "End" will appear in the
display and the end-of-cycle tone will sound.
4. Touch STOP/UNLOCK or open the door to clear the display.
Clocks
The microwave oven must be in standby.
1. Press TIMER button for 3 seconds to enter clock setting. It
will also appear every time the product is plugged into the
power source, or power is back after a power fail.
2. Press +/- button to set the hour.
3. Press START button to confirm.
4. Press +/- button to set the minute.
5. Press START button to confirm the setting.
To Set:
1. Press Timer/Clock button
2. Press +/- button to enter desired time.
3. Press START button. When the set time ends, the
end-of-timer
4. When the Timer countdown is achieve in the display, tone
will sound. Press STOP/UNLOCK to stop the timer.
NOTE: The Timer does not start or stop the microwave oven.
The function can be set only in Standby mode.
Tones ON/OFF
This function allows the user to activate/deactivate all the
sounds played by the appliances, includes button press,
warnings, alarm, even end audio feedback.
Press Steam Clean button and hold for 5 seconds to put into
mute, hold the button again for 5 seconds to turn on the sound.
Cooking End
When the cooking is finished, the display will show the text
"End". A reminder acoustic beep will signal.
1. After the Cooking End, If you press the STOP/UNLOCK
button, takes out the food and closes the door again, the
interface will display the clock, it will switch to 1-step door
opening.
2. If you will not remove the food within 30 minutes, it will
consistently display "END" for 30 minutes, and automatically
return to standby mode and unlock after 30 minutes and it
will switch to 1-step door opening.
To use Sensor Menu
(Dinner Plate/Reheat, Cook Menu)
1. Place food on the turn table and close the door.
2. Touch the desired menu control.
3. Touch START, the running segment animation will appear
in the display. The microwave oven will start and sensor
cooking will begin.
The running segment will remain in the display until the
sensor has determined the remaining cook time.
4. When the cycle end, "End" will appear in the display and the
end-of-cycle tones will sound.
5. Touch STOP/UNLOCK or open the door to clear the display.
(Note: Sauce, Soup, Beverage in Reheat Menu without using
Sensor cooking).
Timer
11
Advertisement
Table of Contents
