Table of Contents
Advertisement
Quick Links
GB
A. Programme selector
B. "Start delay" button
C. Programme sequence indicator
(over the line)
Start delay indicator (under the line)
D. "Variable spin" button
E. "Start/Pause" button
F. "Reset" button
G. "Door open" indication
Care
Programme
Labels
Cotton
Cotone
40 - 60 - 95 °C
40 - 60 - 95°C
Synthetics
Sintetici
30 - 40 - 60 °C
30 - 40 - 60°C
Delicates
Delicati
30 - 40 °C
30 - 40°C
Daily load
Misti
40 °C
40°C
Quick wash
Rapido
30 °C
30°C
Wool
Lana
20 - 40 °C
20 - 40°C
Lavaggio a
Handwash
mano
30 - 40 °C
30 - 40°C
Risciacquo &
Rinse & Spin
–
Centrifuga
Spin
Centrifuga
–
Gentle Spin
Centrifuga breve
–
Drain
Scarico
–
N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing.
PROGRAMME CHART
B
Max.
Type of wash / Notes
Load
- for temperature selection, respect the manufacturer's recommendations on the care label
kg
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton
and linen.For washing heavily soiled laundry, the "Prewash" option can be selected.
5.0
Selecting "Cotton 95", this programme eleiminates bacteria, ensuring sanitization of your laundry. The
bacteria removal efficiency has been tested following a similar methodology to the NF EN 13697 standard
of Nov. 2001.
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon,
2.5
Nylon).
1.5
Curtains and delicate clothing, dresses, skirts, shirts and blouses.
3.0
Slightly to normally soiled textiles made of cotton and/or synthetics.
3.0
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton.
1.0
Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable.
Textiles made of linen, silk, wool and viscose marked as "handwashable".
1.0
A very gentle spin is used in this programme.
5.0
Same as the last rinse and the final spin in the "Cotton" programme.
5.0
In this programme spinning is intensive. Same as the spin cycle in the "Cotton" programme.
1.0
In this programme spinning is gentle. Same as the spin cycle in the "Wool" programme.
–
Drain only - no spinning.
C
I
H
J
D
E
A
This washing machine is equipped with
automatic safety functions which detect and
diagnose faults at an early stage and react
appropriately:
G
H. "Service" indication
I. "Water tap closed" indication
J. "Clean pump" indication
F
1)
Do not use liquid detergent for main wash if you
have activated prewash option.
2)
Do not use liquid detergent.
3)
For improved garment care, spin speed is restricted
to 400 rpm in this programme.
Detergents and Additives
Special options
Pre-
Main
Softener
Start
Pre-
wash
Wash
delay
wash
Avvio
Pre-
Lavaggio
ritardato
lavaggio
1)
2)
Yes
1)
2)
Yes
1)
2)
Yes
2)
–
Yes
–
2)
–
Yes
–
2)
–
Yes
–
2)
–
Yes
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Max.
Spin
Cold
Variable
wash
spin
Speed
Centrifuga
a freddo
rpm
Max
Max
Max
Max
Max
Max
3)
400
–
Max
–
Max
–
Max
–
–
–
5019 612 10180
Advertisement
Table of Contents
Related Manuals for Smeg TLS6-1
Summary of Contents for Smeg TLS6-1
- Page 1 - for temperature selection, respect the manufacturer's recommendations on the care label ritardato lavaggio a freddo Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.For washing heavily soiled laundry, the “Prewash” option can be selected. Cotton Cotone Selecting “Cotton 95”, this programme eleiminates bacteria, ensuring sanitization of your laundry.
- Page 2 “Door open” indication lights up. To cancel the “Start delay” To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water 1. Turn the programme selector to the “Off/O”...
-
Page 3: Definition Of Use
5. Drain hose c. Remove the bottom protection by tilting • Connect the drain hose to the siphon or hook it and turning the washing machine on one over the edge of a sink with the “U” bend (see rear bottom corner. -
Page 4: Precautions And General Recommendations
After- • Before scrapping, cut off the power cable so that the Sales Service. The power cable must only be washing machine cannot be connected to the mains. -
Page 5: Installation
MUST be removed. 1. Unscrew the two screws “A” and the four screws “B” with a flat screwdriver or a No. 8 hex nut box spanner. 2. Remove the transport bracket. 3. Replace the four outer screws “B” on the machine and tighten them. - Page 6 • If the flexible hose is damaged, unplug the washing machine from the mains immediately, turn off the tap and replace the hose. If the flexible hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales Service or from your dealer).
-
Page 7: Electrical Connection
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a plug, you should fit a suitable new, good quality plug by following the instructions in (2) below. -
Page 8: Before The First Wash Cycle
BEFORE THE FIRST WASH CYCLE To remove any residual water used in testing by the manufacturer, we recommend that you carry out a short wash cycle without laundry. 1. Open the tap. 2. Close the drum flaps. 3. Add a small amount of detergent (maximum 1/3 of the quantity the detergent manufacturer recommends for lightly soiled laundry) to the main wash chamber of the detergent dispenser. -
Page 9: Loading The Laundry
(for “1c”). 3. Place the items of laundry into the drum one by one. Do not exceed the maximum load of the programmes indicated in the separate programme chart. -
Page 10: Detergents And Additives
• Starch (dissolved in water; maximum 100 ml) Observe the “MAX” level marks for powder detergent liquid detergent and fabric softener For programmes without prewash and temperatures from cold to 40°C, it is recommended to use liquid detergents to avoid whitish residues on the laundry. GB 8... -
Page 11: Using Chlorine Bleach
We recommend to check and clean the filter regularly, at least two or three times a year. Especially: • if the appliance is not draining properly or if it fails to perform spin cycles. • if the “Clean pump” indication lights up. -
Page 12: Care And Maintenance
Note: Do not submerge the hose in water. Safety valve inspection 5. Screw the flexible hose back onto the tap by hand. Do not use window pliers (risk of squashing the joint). 6. Turn on the tap and check that the connections are water-tight. -
Page 13: Appliance Exterior And Control Panel
6. Open the drum: you can recover the object through the hole in the drum. 7. Refit the blade from inside the drum: Position the plastic tip above the hole on the right side of the drum. 8. Then slide the plastic blade from right to left until it clips. -
Page 14: Troubleshooting Guide
TROUBLESHOOTING GUIDE Your washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and allow you to react appropriately. These faults are frequently so minor that they can be removed within a few minutes. - Page 15 • Safety valve inspection window of your water supply hose is red (provided “Water tap closed” your appliance has a water supply hose as shown on picture “A” - see previous chapter “Care and Maintenance”); replace the hose by a new one available through our After-Sales Service or your specialist dealer.
- Page 16 If faults persist, unplug the appliance, turn off the water tap and contact our After-Sales Service (see next chapter). If your washing machine has no time display, check which of the previously described situations could be the origin of the fault and follow the corresponding instructions. GB 14...
-
Page 17: Before Contacting After-Sales Service
5. To facilitate moving the machine, pull the handle situated at the bottom front (if available on your model) out a little by hand and pull it out to the stop with the foot. Afterwards push the handle back into the original stable position.