1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Washer
  5. SWF1600
  6. Instruction manual

Smeg SWF1600 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

WASHING MACHINE
INSTRUCTIONS MANUAL
GB
1

Advertisement

Table of Contents
loading

Related Manuals for Smeg SWF1600

Summary of Contents for Smeg SWF1600

  • Page 1 WASHING MACHINE INSTRUCTIONS MANUAL...

  • Page 2: Table Of Contents

    8. Control panel symbols This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and Electronic Equipment.

  • Page 3: The New Washing System

    Washing times have also been reduced. Pre-washing is only recommended for very dirty laundry. Please read the operating instructions with care in order to take full advantage of all the features offered by this washing machine. Warning! Please read all the instructions contained in this manual in order to understand how to operate this appliance correctly and safely.

  • Page 4: Safety Warnings

    If the appliance is not connected to the electrical power supply by means of a plug, it is necessary to install an isolation switch with a contact opening gap of at least 3 mm.
  • Page 5 Before removing laundry from the washing machine, make sure the drum has stopped moving. Always switch off the appliance after use to avoid wasting electricity. Leave the door ajar between one wash and the next in order to keep the gasket in good condition. Prolonged inactivity.

  • Page 6: Installation Instructions

    Do not turn the machine upside down and do not place it on its side. • Keep all the components used to block the drum assembly as they will be needed if you decide to move the appliance in future.

  • Page 7: Positioning And Levelling

    • If the water pipe is new or has not been used for a long time, let a certain amount of water run before attaching the inlet hose. This stops any deposits of sand and other impurities from clogging the filters used by the machine to protect the water inlet valves.

  • Page 8: Electrical Connection

    Do not bend or obstruct the hose as this will reduce the flow of water. • Any extensions to the drain hose must not exceed 1 metre, they must have the same internal diameter and must not be obstructed in any way.

  • Page 9: Description Of Controls

    4. DESCRIPTION OF CONTROLS 4.1 CONTROL PANEL All the commands and controls of the appliance are assembled together on the front panel. Models without delayed start option Models with delayed start option Description of controls Open door button ON-OFF and programme selection knob...
  • Page 10 To find out which of the first 3 pieces of information are hown on the display, check which of the LED's, C, D, or N (the tter for models featuring the delayed start option) is lit. Press the button repeatedly to select the required spin Select spin speed button or speed.
  • Page 11 This button reduces the overall duration of the washing cycle. This Quick wash Button option is used to wash small loads or less dirty washing in less time. The bleach stage is skipped when the Quick Wash button is pressed (for models with bleach function).
  • Page 12 The default value is 0 hours 0 minutes and each time the button is pressed it increases by 30’ up to 12h and by 60’ for the following 12 hours, up to 24 hours. The LED lights up while the delayed start time is being Select delayed start button selected and remains on until the programme starts.

  • Page 13: Washing Instructions

    Before opening the door, wait 1 or 2 minutes after the programme ends (“End” LED on) to allow the safety device to disengage. Make sure there is no water in the tub and that the drum is not moving. Open the door by pressing the “Open door” button on the front panel and pulling it open.

  • Page 14: Loading The Washing

    Where possible, save electricity by washing full loads divided by type of fabric. Introduce loose washing and alternate large items with small ones. For the first few times, weigh the loads of washing and then rely on your judgement. Average weights of common garments are shown below: 5.4 LOADING THE WASHING...
  • Page 15 Pour the total quantity of detergent indicated on the packs into compartment “2” of the detergent tray. Very dirty washing Choose a programme with prewash. Add ¼ of the recommended quantity of detergent into compartment “1” of the detergent tray and ¾ of the detergent into compartment “2”. Attention! •...
  • Page 16 ), the relative LED lights up and the display visualises the maximum speed envisaged for the selected washing programme. Press the button repeatedly. Speed decreases by 100 rpm every time until the spin cycle reaches 0 rpm and is disabled.

  • Page 17: Starting The Washing Programme

    The new washing cycle will be performed starting from the beginning. If the tub is already full of water, the new programme will omit the filling phase. To resume the cycle, press Start-Pause again.
  • Page 18 If the no-spin option was selected during the initial spin speed set up phase and the machine stops with the tub full (spin speed 0), STOP appears on the display at the end of the washing programme, alternating with 0000 (spin speed 0) and the spin LED lights up.

  • Page 19: Cleaning And Maintenance

    6.3 CLEANING THE DRAIN PUMP Only clean the drain pump if it is obstructed by buttons, hairpins and the like and the water cannot drain. In this case, proceed as follows. Remove the plug from the socket to disconnect the machine from the electrical power supply.

  • Page 20: Cleaning The Water Inlet Filter

    MODEL A – Insert the lower part of the cover first. Then secure it by turning the plastic buttons a quarter turn clockwise. The slots in the buttons must be horizontal. MODEL B – Insert the lower part of the cover first and then push it towards the base plate until it clicks into place. 6.4 CLEANING THE DETERGENT TRAY Keep the detergent tray free from scale.

  • Page 21: Troubleshooting

    If the machine does not work, before calling the Service Centre and spending money unnecessarily, check that the operations indicated in this troubleshooting table have been performed.
  • Page 22 No water for washing. See point 2 on the troubleshooting table. The water does not drain. See point 4 on the troubleshooting table. For all other error codes, contact the nearest Assistance Centre after disconnecting the power supply and closing the water tap.

  • Page 23: Control Panel Symbols

    8. CONTROL PANEL SYMBOLS PROGRAMS OPTIONS OTHER SYMBOLS DRYING WATER INCREASE FABRIC CONDITIONER NO SPIN OR STOP WHIT HAND WASH OPEN DOOR FULL TUB PRE-WASH DELAY TIMER START-PAUSE RINSES DELICATES START DRAIN AND SPIN ECONOMY CYCLE WASH SECTION QUICK WASH...
  • Page 24 Wash at 40°C, rinses, drain and spin at selected speed (max. 900 rpm) 40° ○ ○ ○ Very dirty resistant synthetics 60° Prewash 2,5 Prewash at 35°C, wash at 60°C, rinses, drain and spin at selected speed (max. 900 rpm) START - PAUSE EXTRA RINSE DELICATES SPIN DELAYED START EASY-IRON...

Table of Contents