Smeg STL120 User Manual page 2

CONSUMPTION DATA
Temperature
Programme Selector
(°C)
Cotton 95
Cotton 60
Cotton 40
Synthetics 60
Synthetics 40
Daily Mixed 40
Delicates 40
Rapid 30
Wool 40
Silk 30
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the
values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The data on
the "Energy Label" refer to the programme "Cotton 60°C".
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the
household conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump
drains the water out.
PREPARATION OF WASH CYCLE
1. Close the drum doors and check that they are
properly locked.
2. Add detergents and additives into the dispenser to
no more then the "MAX" level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Chlorine bleach
• Stain remover agents
• Anti-scale agents (if necessary)
3. Turn the programme selector knob to the
desired programme.
The remaining time display shows the duration
of the chosen programme (in hours and
minutes) and the indicator light of the "Start/
Pause" button flashes.
The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
The preselected temperature can be altered by
pressing the "+" or "-" button.
SELECT THE DESIRED OPTION
When you select an option authorized by the
programme, the corresponding indicator
lights up, except if the combination of
programme, additional options and
temperature is not possible.
Load Water Energy Approx. Programme
(kg) (l) (kWh) (hours : minutes)*
5.0 49** 1.60
5.0 48 0.95
5.0 48 0.60
2.0 54 0.70
2.0 50 0.50
3.0 45 0.45
1.5 50 0.50
3.0 35 0.40
1.0 50 0.50
1.0 35 0.40
"Easy Ironing" button
• Can be used together with "Cotton",
"Synthetics" and "Daily Mixed" programmes to
make ironing easier.
• Increases the water quantity in rinsing and the
clothes are spun in a softer manner.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt).
"Intensive Rinse" button
• The amount of water is increased to ensure a
more intensive rinse.
• This option is particularly suitable for areas with
very soft water or washing linen laundry for
people with skin allergies.
"Rinse Hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from fading.
• This option is particularly recommended for the
"Synthetics", "Delicates" and "Daily Mixed"
programmes.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme with "Rinse Hold" stops
when the "Rinse Hold" indicator light flashes on the
"Programme Sequence Indicator".
Appliance in "Rinse Hold":
• Press the "Rinse Hold" button again: the
programme will terminate automatically with the
Duration selected spin cycle.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
2:05
programme and press the "Start/Pause"
2:05
button again.
2:00
"Spin Speed Reduction" button
1:30
• Every programme has an automatically allocated
1:15
maximum spin speed.
1:00
• Press the button to set another spin speed.
• If the spin speed "0" is selected, the final spin is
0:45
cancelled, but not the intermediate spins. The
0:30
programme ends with a drain cycle.
0:45
START DELAY
0:35
The "Start Delay" button allows the user to run the
machine at his convenience, for example at night
when electricity is cheaper.
• Select programme, temperature and options.
• Press the "Start Delay" button several times to
select the delay time by 1 to 19 hours;
• Press the "Start/Pause" button. The indicator
light of the "Start/Pause" button lights up and
the lamp of the "Start Delay" button flashes.
• The time delay indication disappears when the
programme starts and is replaced by the
remaining time.
• The number of hours preselected can be reduced
later by pressing the "Start Delay" button again.
To cancel the "Start Delay" option
• Turn the programme selector to the "
• Reselect the desired programme and options
and press the "Start/Pause" button.
PROGRAMME START
Turn on the tap and press the "Start/Pause"
button. The indicator light of the "Start/Pause"
button lights up. The indicator lamp shows the
sequence reached by the programme. After starting
the programme, the programme sequence indicator
signals the Wash, Rinse and Spin phases.
Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
LID LOCK
For safety reasons, the lid is locked during certain
phases of the cycle. At the end of the cycle or during
an interruption, the lid unlocks automatically after
about 1 minute.
RED INDICATIONS
"Water Stop"
Lighting up of the Aquastop indication can be caused
by a leak in the appliance or hose. Please refer to the
"Troubleshooting Guide" in the Instructions for
Use.
"Water Tap"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
END OF WASH CYCLE
• The remaining time is on "0: 00" and the "End"
lamp lights up.
1. Turn the programme selector to the "
position.
2. Turn the tap off.
3. Open the lid and the drum doors and unload the
machine.
CHANGE THE PROGRAMME OR OPTIONS
DURING THE CYCLE
1. Select the new programme using the
programme selector. If necessary, select the
additional options and the spin speed. The
luminous indicator of the "Start/Pause"
button flashes.
Note: the "Start Delay" and "Prewash" options
cannot be selected after a programme change.
2. Press the "Start/Pause" button. The new
programme selected continues at the same
" position.
position where the previous programme was
interrupted.
Note: Do not add detergent for this
programme.
PAUSE/INTERRUPT A PROGRAMME
If, for any reason, you wish to interrupt the
programme for a certain time and continue it later:
1. Press the "Start/Pause" button. The light
flashes.
2. After the desired pause, press again on the
"Start/Pause" button.
CANCEL PROGRAMME
1. Set the programme selector to "Drain".
2. Press the "Start/Pause" button to start the
"Drain" programme.
5019 612 10101
"