Download Print this page

Advertisement

14-18
AGE
STEAM EDUCATION
PRO
ASSEMBLY GUIDE
H-CELL 2 .0
www.h2grandprix.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the H2 GRAND PRIX Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Horizon Educational H2 GRAND PRIX Series

  • Page 1 14-18 STEAM EDUCATION ASSEMBLY GUIDE H-CELL 2 .0 www.h2grandprix.com...
  • Page 2: Table Of Contents

    STEAM EDUCATION TABLE OF CONTENTS SAFETY INFORMATION UNBOXING ASSEMBLY GUIDE FUEL CELL TEST TROUBLESHOOTING SERIES VISIT H2GP WEBSITE H-CELL 2.0 21st century power system for 1/10 RC hobby racing. Developed for H2 Grand Prix Series. www.h2grandprix.com H-CELL 2.0 ASSEMBLY GUIDE...
  • Page 3: Safety Information

    STEAM EDUCATION SAFETY INFORMATION PLEASE READ BEFORE PROCEEDING TO ASSEMBLY AND STARTING THE H-CELL FOLLOW THE INSTRUCTIONS OUTLINED BELOW TO FULLY ENJOY OPERATING YOUR 30W HYDROGEN FUEL CELL            Never touch any rotating parts as your finger, hair, clothes etc. may get caught  leading to serious injury. When not in use, always disconnect and remove the battery and hydrogen cartridges (HYDROSTIK, HYDROSTIK PRO). ...
  • Page 4: Unboxing

    STEAM EDUCATION UNBOXING H-CELL 2.0 BEFORE YOU START, PLEASE CHECK THAT YOUR PACKAGE IS UNDAMAGED AND CONTAINS ALL THE LISTED COMPONENTS. THE H-CELL 2.0 PACKAGE CONTAINS: FUEL CELL HYDROGEN CARTRIDGES PRESSURE REGULATORS FUEL CELL CONTROL UNIT TUBING AND FASTENERS PRESSURE SWITCH DO NOT CONTINUE TO ASSEMBLY IF YOU FIND ANY OF THESE PARTS MISSING AND CONTACT US IMMEDIATELLY.
  • Page 5 STEAM EDUCATION ASSEMBLY STEP BY STEP ACTION TUBING CONNECTIONS 1. Place everything on the table. 2. Open your tubing bag. 3. Prepare 7 silicon tubes (D), filter (B), four-port connector (C). You will also need two pressure regulators (A). Do not disconnect the silicon tubing from the fuel cell yet (E).
  • Page 6 STEAM EDUCATION ASSEMBLY STEP BY STEP ACTION TUBING CONNECTIONS 5. Connect other silicon tubes accordingly:   - two on both ends of the filter (A)   - one on metal end of both solenoid valves  inlet and outlet (B)   - one to the bottom inlet of the white pressure switch (C) 6.
  • Page 7 STEAM EDUCATION ASSEMBLY STEP BY STEP ACTION ELECTRONICS 6. Connect the controller box with the fuel cell (A) 7. Connect the controller box to the charged battery (B) 8. Your H-Cell 2.0 is assembled and ready for test! H-CELL 2.0 ASSEMBLY GUIDE...
  • Page 8 STEAM EDUCATION TEST YOUR FUEL CELL STEP BY STEP ACTION 1. Connect full Hydrostiks and tighten them firmly into the regulators (A) 2. You should hear a „click“ sound from the pressure switch (B) 3. Turn ON the fuel cell controller (C) 4. The fuel cell should start running and the fuel cell fans turn blue (D) 5. To make sure that the fuel cell works properly let it work for at least 30 seconds,  you should pay attention to three actions: - fuel cell fans light blue (D) - output valve is purging every 10 seconds (E)
  • Page 9 STEAM EDUCATION OPERATION OF H-CELL 2.0 UNDERSTANDING THE LED INDICATORS IN THE FUEL CELL CONTROL UNIT, WILL HELP YOU TO UNDERSTAND THE FUEL CELL OPERATION AND CONTROL DURING THE RACE. As stated earlier, the fuel cell works properly if, the fuel cell fans light blue, the output valve is purging every 10 seconds and the green LED light stays on.
  • Page 10 STEAM EDUCATION TROUBLESHOOTING FULL TEST PROCEDURE, STEP BY STEP ACTION Make sure you have charged Hydrostiks and batteries. 2. Check all silicon tubing connections: two Hydrostiks, pressure switch, input valve (metal side) connected via four-port connector • input valve (plastic side) to fuel cell • fuel cell to output valve (metal side) • output valve (plastic side) to air 3.   Check all electrical connections: • pressure switch to FCCU • FCCU to fuel cell • FCCU to battery 4.   Screw in both Hydrostiks at once: •...
  • Page 11: Troubleshooting

    STEAM EDUCATION TROUBLESHOOTING After turning on the control box switch, the red light in the control box flashes, while the green light disappears. This indicates the battery is drained and needs to be charged.  1) Charge the battery. 2) Check the battery connection to the fuel cell system and reconnect it again.  After turning on the control box switch, the red light in the control box flashes, while the green light is on.
  • Page 12: H-Cell

    TIME FOR HYDROGEN EDUCATION H-CELL 2.0 ASSEMBLY GUIDE Developed for H2 Grand Prix Series. www.h2gp.com...

This manual is also suitable for:

H-cell 2.0H2gp h-cell 2.0