Table of Contents
Advertisement
Intake grille installation
(1) The fi xing axle of the intake grille is installed on the Panel.
(2) Lay down the intake grille.
Knob
9.2. Front panel / control cover removal and installation
* In this description, the intake grille and wire cover already has been removed.
9.2.1. Front panel / control cover / under cover removal
(1)
Remove intake grille (Reference the intake grille removal.)
(2)
Remove wire cover.
(3)
Remove the 4 screws.
(4)
The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.
Wire
Hooks
Screws
cover
(2 position)
9.2.2. Front panel / control cover / under cover installation
(1)
Firstly, fi t the lower part of the front panel, and insert top and bottom hooks. (3 top
sides, 6 bottom sides)
(2)
3 screws is attached.
(3)
The wire cover is attached.
(4)
The intake grille is attached.
Body
Bottom holes
(6 position)
Top holes
(3 position)
Body
Center Bottom hooks
(2 position)
Please take caution when removing or installing the front panel. If the front panel falls,
there is a risk of injury.
10. TEST RUN
Check items
(1) Is operation of each button on the remote control unit normal?
(2) Does each lamp light normally?
(3) Do air fl ow direction louvers operate normally?
(4) Is the drain normal?
(5) Do not have an abnormal noise and vibration during operation?
• Do not operate the air conditioner in test run for a long time.
[Operation method]
Before starting the test run, wait for 1 minute after connecting the power supply.
By the wireless remote controller
• To start the test run, press the "START/STOP(
the remote controller by using the tip of a ballpoint pen or other small object.
By the indoor unit
• To start the test run, keep on pressing the indoor unit button for more than 10 seconds.
• To end test operation, press the remote controller "START/STOP(
(When the air conditioner is running by pressing the "TEST RUN" button, the
"OPERATION" Lamp and "TIMER" Lamp will simultaneously fl ash slowly.)
En-8
Intake grille
Mounting shaft
Bearing
Front panel
Front panel
Front panel
Bottom hooks
(6 position)
Front panel
Top hooks
(3 position)
Center hooks
Front panel
(2 position)
CAUTION
)" button, the "TEST RUN" button on
)" button.
11. REMOTE CONTROLLER INSTALLATION
Check that the indoor unit correctly receives the signal from the remote controller, then
install the remote controller holder.
Do not install the remote controller holder in the following conditions:
• Any places exposed in direct sunlight
• Positions affected by the heat from a stove or heater
11.1. Remote controller holder installation
• Install the remote controller a maximum distance of 7 m from the remote control signal
receiver. After installing the remote controller, check that it operates correctly.
• Install the remote controller holder to a wall, pillar, etc. with the tapping screw.
Remote controller
holder
Tapping
screws
(small, ac-
cessories)
12. FUNCTION SETTING
Perform the Function Setting according to the installation conditions using the remote
controller.
• Confi rm whether the wiring work for outdoor unit has been fi nished.
• Confi rm that the cover for the electrical enclosure on the outdoor unit is in place.
• This procedure changes to the Function Settings used to control the indoor unit
according to the installation conditions. Incorrect settings can cause the indoor unit to
malfunction.
• After the power is turned on, perform the Function Setting according to the installation
conditions using the remote controller.
• The settings may be selected between the following two: Function Number or Setting
Value.
• Settings will not be changed if invalid numbers or setting values are selected.
Entering the Function Setting Mode
While pressing the FAN button and SET TEMP. (
button to enter the function setting mode.
STEP 1
Setting the Remote controller Custom Code
Use the following steps to select the custom
code of the remote controller. (Note that the air
conditioner cannot receive a custom code if the
air conditioner has not been set for the custom
code.) The custom code that is set through this
process are applicable only to the custom in the
FUNCTION SETTING. For details on how to set
the custom code through the normal process, refer
to "Remote controller custom code".
1
Press the SET TEMP. (
) (
) button to
change the custom code between
→
Match the code on the display to the
air conditioner custom code. (initially set to
be selected, press the MODE button and proceed to STEP 2.)
2
Press the MODE button to accept the custom code, and proceed to STEP 2
The air conditioner custom code is set to
Contact your retailer to change the custom code.
The remote controller resets to custom code
controller are replaced. If you use a custom code other than custom code
the custom code after replacing the batteries.
If you do not know the air conditioner custom code setting, try each of the custom
codes (
→
→
→
) until you fi nd the code which operates the air condi-
tioner.
CAUTION
1 Set
2 Push
Remote
controller
CAUTION
) simultaneously, press the RESET
→
→
) (If the custom code does not need to
prior to shipment.
when the batteries in the remote
*1
, reset
Advertisement
Table of Contents
