Smeg S600TL1 Manual page 20

CONSUMPTION DATA
Temperature
selector
Programme
(°C)
Cotton 95
Cotton
60
Cotton
40
Synthetic 60
Synthetic 40
Delicate
40
Wool 40
Silk 30
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the "Energy Label" refer to the programme "Cotton 60°C".
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
PREPARATION OF WASH CYCLE
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergents and additives into the dispenser to
no more then the "MAX" level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softener and conditioners
• Chlorine bleach
• Stain remover agents
• Anti-scale agents (if necessary)
3. Turn the programme selector knob to the
desired programme.
4. Turn the temperature selector knob to the
desired temperature.
Load Water Energy Approx. Programme
Duration
(kg) (l) (kWh) (hours : minutes)
5,0 63* 1,80
5,0 55 0,95
5,0 55 0,55
2,0 56 0,80
2,0 56 0,40
1,5 60 0,55
1,0 60 0,50
1,0 60 0,30
SELECT THE DESIRED OPTION
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
"No Spin" button
• Especially for delicate garments to avoid wear and
tear caused by the spin.
Note: with the "Cotton" and "Synthetics" programmes
a short spin cycle is provided in any case, even if the
exclusion has been selected, in order to optimize rinsing
results.
"Half Load" button
• Can be used for small loads and lightly soiled laundry.
• Reduces the water consumption especially during
the rinses.
"Intensive Rinse" button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water or washing linen laundry for people with
skin allergies.
"Rinse Hold" button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from fading.
• This option is particularly recomended for the
"Synthetic" and "Delicate" programmes.
• This function is particularly useful if you want to
2:05
postpone spinning to a later time, or if you want to
2:05
drain only.
Note: the programme selector knob stops on
2:05
Appliance in "Rinse Hold":
1:30
• Press the "Rinse Hold" button again: the programme
1:30
will terminate automatically with the selected spin
0:45
cycle.
• If you do not wish to spin the clothes, press the
0:40
"On/Off" button, turn the programme selector
0:50
knob to the "Drain" programme and press the
"On/Off" button again.
PROGRAMME START
Turn on the tap and press the "On/Off" button.
The indicator light of the "On/Off" button lights up.
Note: If there is a power interruption or if the appliance
is disconnected during the cycle, the programme will run
again from the point where it was interrupted.
END OF WASH CYCLE
• The programme selector knob is in the Stop position.
1. Press the "On/Off" button to switch off the
machine.
2. Cancel the options.
3. Turn the tap off.
4. Wait for the lid to unlock (about 1 minute).
5. Open the lid and the drum doors and unload the
machine.
CHANGE THE PROGRAMME DURING THE
WASH CYCLE
1. Switch off the machine by pressing the "On/Off"
button.
2. Select the new programme.
3. Start programme by pressing the "On/Off" button
again.
.
PAUSE/INTERRUPT A PROGRAMME
If, for any reason, you wish to interrupt the programme
for a certain time and continue it later:
1. Press the "On/Off" button.
2. After the desired pause, press again the "On/Off"
button.
CANCEL PROGRAMME
1. Switch off the machine by pressing the "On/Off"
button.
2. Set the programme selector to "Drain".
3. Press the "On/Off" button again to start the
"Drain" programme.
5019 612 10071