Related Manuals for Smeg S600TL1
Summary of Contents for Smeg S600TL1
-
Page 1: Table Of Contents
CONTENTS BEFORE USING THE WASHING MACHINE FIRST WASH CYCLE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES PROGRAMME SELECTION CLEANING THE FOREIGN BODY TRAP DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE... -
Page 2: Before Using The Washing Machine
• The technical data (voltage, power and fuses) are corner. given on the rating plate on the rear of the d. Open the lid by pressing it slightly down while raising washing machine. the handle. Remove the polystyrene cushion. • The washing machine must be connected e. -
Page 3: First Wash Cycle
FIRST WASH CYCLE We recommend that the first wash cycle be carried out empty. This will remove any residual water used in the factory checks. 1. Turn on the tap. 2. Close the drum flaps. 3. Pour a small amount of detergent (about 30 ml) into the detergent dispenser 4. -
Page 4: Description Of The Washing Machine
• Size pillow cases. Wash items of different sizes in the same load to 2.Empty pockets improve efficiency and distribution in the drum. Coins, safety pins and similar items can damage your washing machine drum and tub. - Page 5 1. Open the machine lid. 2. Open the drum by pressing the small flap and holding the large flap. 3. Place the items of laundry in the drum one by one without compressing them. Follow loads recommended in the “programme chart”: overloading will result in unsatisfactory washing results and creased laundry.
- Page 6 2. Open the drum by pressing the button and keep your second hand on the big drum door at the same time. 3. Place the items of laundry in the drum one by one without compressing them. Follow loads recommended in the “Programme chart”: Overloading will result in unsatisfactory washing results and creased laundry.
-
Page 7: Detergents And Additives
Be careful not to fill more than the “MAX” level mark. Do not use liquid detergents for programmes with prewash. For programmes without prewash and temperatures from cold to 40° C, it is recommended to use liquid detergents to avoid whitish residues on the laundry. GB 7... -
Page 8: Programme Selection
5. Turn the spin speed selector knob (if available) to the desired spin speed. 6. Turn the spin speed selector knob to the desired spin speed. If the spin speed “0” is selected, the final spin is cancelled, but not the intermediate spins. The programme ends with a drain cycle. -
Page 9: Cleaning The Foreign Body Trap
9. Insert the foreign body trap again and screw it fully down in a clockwise direction to the stop (until the grip is horizontal). 10. Pour 0.5 litres of water into the machine via the drum and check that water does not leak from the foreign body trap. -
Page 10: Draining Residual Water
5. Let the residual water flow into a shallow basin. 6. Wait until the flow stops. 7. Fix the drain hose again with the clip and replace it with the U- bend. 8. Reconnect the water supply hose and the power plug. - Page 11 Note: For machines equipped with hose type “A”, it must not be submerged in water. 5. Screw the flexible hose back onto the tap by hand. Do not use pliers (risk of squashing the joint). 6. Turn on the tap and check that the connections are water- tight.
-
Page 12: Troubleshooting Guide
*The washing machine does not start, but • the water in the drain hose is frozen. the pilot lamp is on. If water has remained in the drum, you can drain it Check whether: by following the instructions in the chapter •... - Page 13 Turn on water supply (if the machine is switched the foreign body trap”). off, but begins to fill, turn off the water supply and • if the laundry is still too wet at the end of the contact After Sales Service). programme: possibly add other items of clothing Reselect the desired programme, add the and repeat the spin cycle.
-
Page 14: After-Sales Service
4. Eliminate all water from the hoses and the washing machine (see “Draining residual water”). Wait for the water to cool so as to avoid any accidents. 5. To facilitate moving the machine, pull the handle situated at the bottom front (optional on certain models) out a little by hand and pull it out to the stop with the foot. -
Page 15: Installation
Before using the washing machine, the transport bracket at the back MUST be removed. 1. Unscrew the two screws A and the four screws B with a flat screwdriver or a No. 8 hex nut box spanner. 2. Remove the transport bracket. - Page 16 Install the washing machine on a level surface, near to electrical, water and drain connections. If the floor is uneven, adjust the feet (do not insert pieces of wood, cardboard etc. under the feet): 1. Loosen the locknut using the wrench provided.
- Page 17 If the flexible hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales Service or from your dealer). This operation must be carried out exclusively by a qualified technician.
-
Page 18: Electrical Connection
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a plug, you should fit a suitable new, good quality plug by following the instructions in (2) below. - Page 19 Labels °C Cotton with Prelavaggio Max. 95 Heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen. prewash cotone Prelavaggio Synthetics with Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen,Trevira), polyamide (Perlon, –...
- Page 20 The data on the “Energy Label” refer to the programme “Cotton 60°C”. button. * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the 2. Set the programme selector to “Drain”.