Safety Instructions - enphase COMMS-KIT-EU-01 Quick Install Manual

SAFETY
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This guide contains important instructions that you must follow during
installation of the Enphase Communications Kit.
Safety and Advisory Symbols
DANGER: This indicates a hazardous situation, which if not avoided, will
+
result in death or serious injury.
WARNING: This indicates a situation where failure to follow instructions
*
may be a safety hazard or cause equipment malfunction. Use extreme
caution and follow instructions carefully.
✓
NOTE: This indicates information particularly important for optimal
system operation. Follow instructions carefully.

Safety Instructions

DANGER: Risk of electric shock. Risk of fire. Do not attempt to repair the
+
Enphase Communications Kit. It contains no user-serviceable parts. If the
equipment fails, contact Enphase Customer Support for assistance or
replacement equipment (https://enphase.com/contact/support).
DANGER: Risk of electric shock. Do not use Enphase equipment in a
+
manner not specified by the manufacturer. Doing so may cause death or
injury to persons, or damage to equipment.
DANGER: Risk of electric shock. Risk of fire. Only competent personnel
+
should troubleshoot, install, or add parts to the IQ Gateway.
DANGER: Risk of electric shock. All sources to equipment being serviced
+
must be disconnected external to the device. In particular, the storage
system may energize conductors, so storage circuits must ALWAYS be
isolated via circuit breaker or disconnect before working on any portion
of the system.
DANGER: Risk of electric shock. Risk of fire. Only use electrical system
+
components approved for wet locations.
DANGER: Risk of electric shock. Risk of fire. Ensure that all wiring is
+
correct and that none of the wires are pinched or damaged.
DANGER: Risk of electric shock. Risk of fire. Do not work alone. Someone
+
should be in the range of your voice or close enough to come to your aid
when you work with or near electrical equipment. Remove rings, brace-
lets, necklaces, watches etc. when working with batteries, photovoltaic
modules or other electrical equipment.
DANGER: Risk of electric shock. Risk of fire. Before making any connec-
+
tions verify that the circuit breakers are in the off position. Double check
all wiring before applying power.
✓
NOTE: Using unapproved attachments or accessories could result in
damage or injury.
Enphase Customer Support: https://enphase.com/contact/support/
Compliance with EU Directives
This product complies with the following EU Directives and can be
used inthe European Union without any restrictions.
• Electro Magnetic Compatibilty (EMC) directive 2014/30/EU
• Restriction of Hazardous Substances (RoHS) 2011/65/EU
RED Directive Compliance
Hereby, Enphase Energy Inc. declares that the radio equipment
type IQ Battery follows Directive 2014/53/EU.
The full text of the EU declaration of conformity (DoC) is available at:
https://enphase.com/en-gb/installers/resources/documentation
Contact information
Manufacturer:
Enphase Energy Inc.,
47281 Bayside Pkwy, FREMONT, CA,
94538, UNITED STATES of AMERICA, PH: +1 707-763-4784
Importer:
Enphase Energy NL B.V.,
Het Zuiderkruis 65, 5215MV,
's-HERTOGENBOSCH, THE NETHERLANDS,
PH: +31 73 3035859
Environmental Protection
ELECTRONIC DEVICE: DO NOT THROW AWAY. Waste electrical
products should not be disposed of with household waste.
Proper disposal of batteries is required. Refer to your local codes
for disposal requirements.
© 2023 Enphase Energy. All rights reserved. Enphase, the e and CC logos,
IQ, and certain other marks listed at
age-guidelines are trademarks of Enphase Energy, Inc. in the US and other
https://enphase.com/trademark-us-
countries. Data subject to change.
Rev03/05-08-2023