Related Manuals for YARD Commander 125LB
Summary of Contents for YARD Commander 125LB
- Page 1 125LB PUSH SPREADER Instruction & Assembly SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE REV12122023 SP31515...
-
Page 2: Table Of Contents
Table of Contents General Warnings and Rules ................3 Hazard Signal Word Definitions ................4 Controls and Features Identification ..............5 Component & Hardware ..................6,7 Assembly Instructions ................ 8, 9,10,11,12 Operation Instructions ................13,14,15 Spreading Instructions ..................16 Maintenance and Storage & Specification ............17 Parts Drawing &... -
Page 3: General Warnings And Rules
Replace or repair damaged or worn parts immediately. Always check and tighten hardware and assembled parts before operation. Do not exceed equipment maximum load capacity of 125lb. Avoid large holes and ditches when transporting loads. Be careful when operating on steep grades (hill) the spreader may tip over. -
Page 4: Hazard Signal Word Definitions
Hazard Signal Word Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates an imminently hazardous DANGER situation which, if not avoided, will result in death or serious injury. -
Page 5: Controls And Features Identification
1) Handle – Pushes and moves the spreader easily. 2) Flow Control – Controls the flow of material being spread. 3) Hopper – Do not exceed rated load capacity 125lb. 4) Tires / Wheel – Do not exceed recommended rated. -
Page 6: Component & Hardware
CAUTION Read and follow all instructions for assembly and operation. Failure to properly assemble this equipment could result in serious injury to the user or bystanders, or cause equipment damage. PUSH SPREADER COMPONENT PARTS AND ASSEMBLE. Take all parts out of the shipping crate and inspect components to ensure there are no missing pieces before starting to assemble the push spreader follow steps 1 through 5. - Page 7 Component Parts - 7 -...
-
Page 8: Assembly Instructions
Assembly Instructions STEP 1: Installing the Wheels 1. Flip the Frame Assembly upside down and slide the axle bushing and the wheel spacer onto the left side of the axle. 2. Push the left wheel onto the axle. 3. Slip the flat washer Ø16 onto the axle, then insert the cotter pin Ø5x35 through the hole in the axle. 4. - Page 9 STEP 2: Assembling the Support Leg 1. Remove the two partially installed Hex Bolt M8x75, Flat Washer and Lock Nut M8 from the middle of the frame as shown in diagram. 2. Flip the Frame Assembly over onto the wheels. 3.
- Page 10 STEP 3: Installing the Hopper 1. Lower the hopper into the Frame Assembly, carefully line up the hole in the bottom of the hopper with the spindle in the mounting plate of the axle. 2. Using six hex bolt M6 x 40 and six flat washers Ø6, install the hopper to the mounting assembly by passing the bolts through the hopper and mounting tube.
- Page 11 STEP 4: Connecting Handle to the Support Leg 1. Slide the bottom of the handle tube into the top of the support leg and align the two holes as shown in the diagram below with the Adjustment Handle facing the Hopper. 2.
- Page 12 STEP 5: Connecting the Solid Linkage 1. Align the Linkage Bar on the right side of the Handle Assembly as shown in the diagram with the 90-degree end at the bottom near the hopper. 2. Insert the bottom end of the Linkage Bar into the metal hole at the base of the Hopper. 3.
-
Page 13: Operation Instructions
Operation Instructions ADJUSTING THE FLOW 1. The handle adjusts the spreader setting. When the handle is moved to “30”, the adjustable plate is fully open, when at “0”, it is fully closed. 2. Loosen the wing nut on the Bracket and move the adjustment lever handle up or down depending on the amount of material required. - Page 14 Operation Instructions WARNING Before using the push spreader, review the instructions below and safety information before operating. Failure to follow these instructions may result in property damage or injury to the operator or bystanders . USING YOUR SPREADER 1. Inspect your spreader before each use. Make sure the wheels turn easily, and the gearbox moves when the spreader is pushed.
- Page 15 Operation Instructions CAUTION The spreader settings are guidelines only. The spreader should be calibrated prior to application to ensure accuracy. The spreader settings are based on a walking speed of 3 MPH. Walking faster or slower will alter the spread application rate. Exact rates depend upon the spreader itself and the accuracy of the person operating it.
-
Page 16: Spreading Instructions
SPREADING INSTRUCTIONS CALCULATING AMOUNT OF MATERIAL NEEDED To calculate the amount of fertilizer you will need to cover your lawn, divide the coverage amount listed on the label by the weight of the fertilizer bag. For example, a 10LB. bag of fertilizer with coverage of 10,000 square feet will distribute 1LB. -
Page 17: Maintenance And Storage & Specification
Before storing make sure the spreader is clean and dry for years of trouble-free service. Store indoors or protected area during severe weather and winter months. • Specifications Load Capacity ....................125lb Spreader Type ..................Broadcast Hopper Material ................Polypropylene Hopper Dimensions ..............29.5” x 16.5”x13.4”... - Page 18 Parts Drawing - 18 -...
- Page 19 Parts List Ref# Drawing No. Description N512-00020 Hopper 9302-06000-DG Big Flat Washer Ø6 9101-06040-DG Hex Bolt M6x40 N512-00026-DG R Pin Ø3 N512-00009 Bearing N512-00021 Fixed Adjustable Plate N512-00022 Active Adjustable Plate N512-00023-DG Base for Spring 9206-06000-DG Hex Lock Nut M6 N512-00025-DG Spring 9206-08000-DG...
- Page 20 Parts List Ref# Drawing No. Description N570-00009 Handle Cover N514-00002-DG Axle Bushing N512-00002 Crossover Tube 9402-04025-DG Spring Pin Ø4x30 N575-00006-DG Bracket 9101-06020-DG Hex Bolt M6x20 9114-06025-DG Carriage Bolt M6x25 9315-08000-DG Teeth Lock Washer Ø8 N512-00027-DG Connecting Plate N510-00016 Spacer N510-00019 Wing Nut M6 N760-00012 Adjusting Handle...
-
Page 21: Limited Warranty
Limited Warranty Warranty For one year from the date of purchase YTL International will replace for the original purchaser, or repair the spreader. The warranty will not apply to any unit which was not assembled correctly, misused, overloaded or which has been used or operated contrary to our instructions, or which has been repaired or altered by anyone other than an authorized representative.