Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Donnergy GH5000TL
Summary of Contents for Donnergy GH5000TL
- Page 1 HYBRID INVERTER USER MANUAL (V1.0)
-
Page 2: Table Of Contents
Contents ..........21 7.4 LCD display ...........22 7.4.1 The button 1 Notes On This Manual ..........1 ......22 7.4.2 Indicator light & Status 1.1 Validity ................1 1.2 Target Group ..............1 ........23 1.3 Additional Information ..........1 7.5 LCD menu introduction 1.4 Storage Of The Manuals ..........1 7.5.1 operating parameter ........23 1.5 Symbols Used ...............2... -
Page 3: Notes On This Manual
1.1 Validity Manual – Read the Manual! This manual describes the assembly, installation, commissioning and maintenance of the Donnergy hybrid inverter. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. This manual does not cover any details concerning equipment connected to the unit ( e.g. -
Page 4: Safety And Conformity
2 Safety And Conformity DC and AC Breaker Disconnecting the unit securely from the grid and the PV generators, battery using 2.1 Safety Instructions DC and AC breaker. DC and AC breaker shall be able to disconnect all non- ground conductors after installation. -
Page 5: Product Description
3 Product Description Figure 2 3.1 InverterOverview Figure 1 LCD Displaying PV Input Terminals Battery Input Terminals PV Input Switch COM Terminals WIFI Or GPRS Com Module And USB Port AC Output Terminals Spec Label and Inverter Serial No. 3.3 Storage of Inverter If you want to storage the unit in your warehouse, you should choose an appropriate 3.2 Information of the Unit location to store the inverter. -
Page 6: Unpacking
5 Installation and Electrical Connection 4 Unpacking 5.1 Safety Thoroughly inspect the packaging upon receipt. If any damage to the packaging is visible, or if you find that the unit is damaged after unpacking, please notify the distributor immediately. If there is anything damaged or missing, please contact your supplier. Do not dispose of the original packaging. -
Page 7: Selecting The Installation Location
5.2SelectingTheInstallationLocation The inverter should not be installed in direct sunlight, direct heavy water sources or unstable locations. We recommend that the inverters be installed at a location with some cover or protection. This is guidance for the installer to choose a suitable installation location, to avoid potential damages to the device and operators. -
Page 8: Mounting The Inverter With Bracket
AmbientDimensionsUsingInvertersInSeries 5.4 Fixed The Inverter On The Wall There must be sufficient clearance between the individual inverters to ensure that the ambient air from the adjacent inverter is not taken in. If necessary, increase the clearance spaces and make sure there is enough fresh air Falling equipment can cause serious or even fatal injury. -
Page 9: Check Inverter Installation Status
CheckInverterInstallationStatus Position Description Check the mounting of the inverter by trying to raise it from the bracket. The PV Modules inverter should remain firmly attached. PV Side Breaker Please ensure that the correct mounting surface is selected to allow for vibration of the inverter during normal operation. -
Page 10: Connect To The Back-Up
5.6.5 Connect To PV Panel We suggest the AC separate unit spec as follow, Model 4600TL 5000TL 3600TL Risk of electric shock and fire, use only with PV modules, and with a maximum system voltage of 500Vdc per string. Output cable requirements Electric shock hazard, the DC conductors of this photovoltaic system are normally ungrounded but will become intermittently grounded without Product Model... -
Page 11: Connect To The Battery
Figure 18 NOTE Grade Description Value we recommend using the Donnergy appointed lithium battery, because the battery O.D. 10 ~12mm BMS communication has been designed to be compatible with the Donnergy Hybrid C.S.A. 13 ~ 25mm Inverter. Bare Wire Length 10mm... -
Page 12: The Inverter Parameter Setting
5.6.7 ConnectCTClampOrMidApprovedMeterToInverter TheInverterParameterSetting In the system, a CT or mid approved meter must be installed to monitor the Connect to the inverter via the Engineers software to set the battery parameter, grid charger time, inverter discharge time and various other functions. power of the house to decide the inverter status: charge or discharge. -
Page 13: Parallel Operation
7.3Parallel operation 7.4.1, The button 7.4.1, The button 1. Set the master/slave machine. Switch SW1 to ON, that is, the host machine (factor y default host setting),and switch 1. Press “Up” to enter the upper-level menu or the number +1 1. -
Page 14: Lcd Menu Introduction
7.5LCD menu introduction 7.5.2 On the home screen, press ”Up “to enter the main menu screen, which provides the following five options 7.5.1 O perating parameter Press ”Down“ on the home screen to enter the grid, battery, PV, and load information screens Main interface 1.System setting Down... -
Page 15: Advanced Setting
BMS Type, which is used to set the AH count of the battery 7.5.4 Advanced setting ： ： ） （1 automatic identification The AH count is configurable In Advanced Settings, press “Enter ”to enter the sub-menu screen. The sub-menuscreen provides the following eight options: It is displayed in two 1.2 BAT Cap Settings. -
Page 16: System Information
4. Forced battery activation 1. Inverter information 1.Inv information Enter 1.SN 4.Forced to activate Enter 1.Enable 2.SE FW 2.Disable 3.HE FW 4.Model 5. Switch on and off the inverter 5.Statutory 5.Turn on/ off Enter 1.On 2. Battery information This part is displayed in three screens. Press the “Down” or “Up” key to switch 2.Off the screen, which is mainly used to display battery related parameters. -
Page 17: Energy Information
7.5.6 Energy statistics Press “Enter” in the energy statistics item to go to the sub-menu screen. The following four options are displayed 4.Energy statistics Enter 1.Day energy 2.Month energy 3.Year energy 4.Total energy 2.The monthly energy yield, annual energy yield, and cumulative energy yield are 1.Energy yield of the day, This page is used to display the energy yield of the day displayed in the form of numerical values and bar graphs in the form of values and bar graphs... -
Page 18: Start-Up And Shut Down The Inverter
Start-UpAndShutDownOfTheInverter 8.1 Start-UpTheInverter Once a year, turn the rotary switch of the DC switch from the On position to the Off position 5 times in succession. This cleans the contacts of the rotary switch and (1) Connect the AC circuit breaker; prolongs the electrical endurance of the DC Disconnect. -
Page 19: Work Modes
11 WorkModes 13 TechnicalDate Series Hybrid Inverter has the following main work Donnergy Model GH5000TL GH4600TL GH3600TL modes: PV Input（DC） Max. DC input power (W) 7000W 6600W 5200W Max PV input voltage (V) 500V Starting voltage 150V DAYTIME MODE Sting A...
Need help?
Do you have a question about the GH5000TL and is the answer not in the manual?
Questions and answers