Page 1
Wet/Dry Vacuums 240-5236 OPERATOR’S MANUAL CAUTION: To Reduce The Risk Of Injury, User Must Read And Understand Operator's Manual. Save These Instructions For Future Reference.
SAFETY INSTRUCTIONS & WARNINGS The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
Page 4
• Do not allow to be used as a toy. Close of personal injury or damage to your Wet/Dry attention is necessary when used by or near ® Vac, use only MASTERFORCE recommended children. accessories. • To reduce the risk of injury from accidental...
DOUBLE INSULATION INSTRUCTIONS T h i s We t / D r y Va c i s d o u b l e - i n s u l a t e d , A DOUBLE-INSULATED APPLIANCE, NOR eliminating the need for a separate grounding SHOULD A MEANS FOR GROUNDING BE system.
Rear Wheels Bag with Operator’s Handle Wet/Dry Vacuums 4 Screws Manual 240-5236 OPERATOR’S MANUAL Injury, User Must Read CAUTION: To Reduce The Risk Of Manual. Save These Instructions And Understand Operator's For Future Reference. NOTE: The hose and accessories for this vacuum are 1.25” (32 mm) diameter.
Page 7
UNPACKING & CHECKING CARTON CONTENTS Handle Cord Rewind Button Power Switch Power Head Tool Caddy Latch Vacuum Port Collection Rear Wheel Tank Casters Page 6...
GENERAL ASSEMBLY INSTRUCTIONS A Philips head screwdriver driver is required. 4. Remove the contents from inside the collection tank and make sure you have all WARNING: DO NOT PLUG POWER contents as listed on page 5 (Fig. 4). C O R D I N T O P O W E R O U T L E T , M A K E SURE PLUG IS DISCONNECTED BEFORE Fig.
Page 9
GENERAL ASSEMBLY INSTRUCTIONS 7. Your vacuum comes ready for dry vacuum 10. Insert the handle into the slots located on cleaning. If cartridge filter is not installed the top of the power head and secure it with refer to page 15 for filter installation the screws provided.
Page 10
GENERAL ASSEMBLY INSTRUCTIONS POLARIZED PLUG To reduce the risk of electrical shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
DRY VACUUM OPERATION DRY VACUUMING 3. Place filter retainer on top of cartridge filter and tighten by turning the retainer handle WARNING: B E S U R E T O R E A D , clockwise (Fig. 3). UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY INSTRUCTIONS &...
Page 12
DRY VACUUM OPERATION O P E R A T I N G I N S T R U C T I O N S : D R Y 9. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position and VACUUMING unplug the power cord from the outlet 6.
LIQUID VACUUM OPERATION LIQUID VACUUMING WARNING: B E S U R E T O R E A D , Fig. 2 UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS W I T H F LAM MABLE G AS E S, V AP OR S , O R E X P L O S I V E D U S T S I N T H E A I R .
Page 14
LIQUID VACUUM OPERATION 5. Turn the motor on by f lipping the switch to 8. To rewind the cord, hold on to the plug and the ‘I’ ON position (Fig. 6). press the cord rewind button. Do not allow plug to whip when rewinding (Fig. 10). Fig.
MAINTENANCE 1. Verify that the power cord is disconnected 4. Clear all dirt or debris from the collection from the outlet (Fig. 1). tank and hose (Fig. 4). Fig. 4 Fig. 1 5. Clean the foam wet filter by washing it with 2.
INSTALLING & CLEANING FILTERS Installing Cartridge Filter Removing and Cleaning Cartridge Filter 1. Verify that the power cord is disconnected 1. Unlock and remove the filter retainer by from the outlet (Fig. 1). turning retainer handle counter clockwise. 2. Carefully hold and pull the cartridge filter up Fig.
Page 17
INSTALLING & CLEANING FILTERS 2. Unlock the filter door by sliding the lock tab 5. Install the cleaned or new filter (Fig. 6). UP to the unlocked position and pull the door out (Fig. 2 & 3). Fig. 6 Fig. 2 Fig.
INSTALLING & CLEANING FOAM WET FILTER Installing Foam Wet Filter Cleaning Foam Wet Filter 1. Verify that the power cord is disconnected 1. With the removed power head in an upside from the outlet (Fig. 1). down position, carefully remove foam wet filter (Fig.
TROUBLESHOOTING WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE TROUBLESHOOTING. Symptom Possible Causes Corrective Action 1) Check power supply – cord, 1) No power supply. breakers, fuses. 2) Unplug and check the power Vacuum will not operate. 2) Faulty power cord. cord.
The warranty coverage ends when the product becomes unusable for reasons ® other than defects in workmanship or material. If, during normal use, this MASTERFORCE wet/ dry vacuum breaks or fails due to a defect in material or workmanship, simply bring the vacuum ®...
Need help?
Do you have a question about the 240-5236 and is the answer not in the manual?
Questions and answers