Page 1
1.2 system is a trademark of EUTELSAT. The USALS system is a trademark of STAB - patent nr 002249506 The designs and technical data may be modified without warning and remain the property of STAB. Instructions manual ROTOR SAT HH100-HH120 - Page...
Coaxial cable Mechanical limits ±70° Programmable electrical limits from 5° to 65° Fine rotation by impulses of 0,1° Inclination of the rotor on the pole from 15° to 70° Rotor weight 3,2 kg Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 3
Nr 4, 8 MA Stainless steel screws Nr 2 Clamps Nr 4, 8 MA Stainless steel screws Nr 8, ø 8mm Stainless steel washers U BOLT SCREW + WASHER CLAMPS U BOLT CONNECTOR COVER BRACKET NUT + WASHER Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 4
Cable 1 plug. Fit an F-connector on each end of the cable going to the receiver and connect the rotor's REC plug to the plug of your receiver. RECEIVER Scart Cable 2 Cable 1 Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 5
If the previous steps have been correctly carried out, you should now be able to see all satellites including the lower East and West orbital ones. Bolts Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 6
Now you can operate the recalculation (if your receiver gets the function). If not, you have to go back to each memorized position, check the best picture and store all positions one by one. SOUTH WRONG ORBIT IDEAL ORBIT 60° 0° 60° Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 7
11. Autofocus (only for enabled receiver) 11.1 The rotor is provided with a special function called "autofocus": this procedure allows the rotor to focus automatically the satellites before storing. Only some receivers are provided with this command. Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 8
(correct pointing to the South, manual research of all satellites, setting of limits, etc). Since 1999, the main aim of STAB research has been to solve all possible problems connected to installation of the motor and to enable users to buy the STAB motor from their retailer and to install it easily everywhere in the world.
Page 9
The USALS installation procedure is extremely simple. If you are not absolutely certain of the coordinates and the degrees of elevation of the antenna for your installation location, consult the site: www.stab-usals.us or the maps at pages 72- STAB will provide you with all the data of:...
Page 10
Align perfectly the rotor’s supporting journal to the dish axis and tighten the screws. A l i g n t h e D i s h Elevation and tighten the fixing screws. Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 11
TV-screen connected to the receiver or the signal on the strong field meter. Tighten the fixing screws. CONGRATULATIONS!!! Installations and pointing of all satellites have just been completed Instructions manual ROTOR SAT HH100-HH120 - Page...
Page 12
P C - C a r d o r a dish in DISEqC1.2 mode. DiSEqC1.0 receivers. Easy to use, in 5 minutes it enables the dish to be perfectly pointed only with the help of the field strength meter. Instructions manual ROTOR SAT HH100-HH120 - Page...
!R e p e a t m o r e c a r e f u l l y t h e signals are not received. angle. procedures on paragr. 7. 8. Central satellites signals are not received. Instructions manual ROTOR SAT HH100-HH120 - Page...
The motor must not be used for purposes other than those indicated by STAB. The motor has been designed to be supplied by a sat receiver or by a STAB positioner; any other type of supply is strictly prohibited and may cause damage or serious injury.
Need help?
Do you have a question about the ROTOR SAT and is the answer not in the manual?
Questions and answers