Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Adkins INLINE 800
Summary of Contents for Adkins INLINE 800
- Page 1 INLINE 800 A D K I N S POWDER SHAKER SET UP AND OPERATION MANUAL...
-
Page 2: Table Of Contents
1. Unboxing/Set up: page 3-5 2. Description of parts: page 6-7 3. Powder trough part: page 8 4. Powder shaking parts: page 9 5. Internal parts: page 10 6. Input Heating parts: page 11 7. Output/take up parts: page 12 8. -
Page 3: Unboxing/Set Up
Place the box in a position that is flat and level, and that you have sufficient space to unbox and remove the Adkins Inline 800 from the palette. Remove the straps, followed by the lid then the four sides, taking care not to damaged/scratch the Adkins Inline 800. - Page 4 UNBOXING/SET UP Please read before connecting to power and operation The heater hood and side panels are fixed by screws for transportation and need to be removed, and the filter door connection checked. 1. Open the filter door by unscrewing the thumb screw as marked (A) below, it does not require to be removed, just enough so the door can lift and swing open.
- Page 5 If there is any mis-aligmnment the media can move or track off while in operation causing issues. Use a tape measure to check that the front of the Adkins Inline 800 is aligned to your printer. See image below (we recommend a gap of approx 40cm from the printer to the Adkins Inline 800: 7.
-
Page 6: Description Of Parts
DESCRIPTION OF PARTS 13 14 1. Main trip switch/breaker 8. Isolation transformer 2. AC contactor 9. Paper feed gear set 3. 24V power box 10. Powder removing brushless motor 4. Electromagnetic relay On/Off s witch 5. 2-channels driver board 12. Powder shake gear set 6. - Page 7 FRONT VIEW Heater hood fans Heater hood Powder shaker On/Off button Powder trough Main control panel Door latch Emergency stop Extraction fans Smoke extraction door Front preheating panel Extraction valve Powder collection cover Adjustable film Input sensor Wind down adjustable feet REAR VIEW Heater hood fans Heater hood...
-
Page 8: Powder Trough Part
POWDER TROUGH PART 1. Powder trough Keep the powder trough dry and clean, and avoid moisture to prevent powder from coagulating and jamming. page 8... -
Page 9: Powder Shaking Parts
POWDER SHAKING PART 1. Suction roller. 2. Conveyor belt. 3. H igh frequency powder removal system 4. Powder holder plates. page 9... -
Page 10: Internal Parts
INTERNAL PARTS 1. Smoke exhaust filter panel. 2. Oil drain valve. 3. Heating elements. 4. Mesh conveyor belt. 5. Exhaust fan. page 10... - Page 11 OUTPUT/ TAKE UP PART 1. Oven hood. 2. Insulation a e b ffl . Fan cooling device. Suction cooling device. 5. Film take up motor and take up shaft. (Cardboard core required for use with the take up) Film Tension bar. page 12...
-
Page 12: Input Heating Parts
INPUT HEATING PART 1. Extraction fans. Front preheating panel. Adjustable film Input sensor. page 11... -
Page 13: Main Control Panel Layout
MAIN CONTROL PANEL LAYOUT Main menu Auto: Used to start automatic mode (automatic production) Manual: used to enter manual mode (manual operation) Heat Temp: Dispays current oven temperature Pre Temp: Displays current preheat plate heating temperature Powder: Displays current powder on film, measured by the powder weight sensor Dusting: Click to toggle the dusting function on/off... -
Page 14: Io Control Panel
IO FUNCTION PANEL FILM IN: Front film sensor, when it senses film, it will turn grey, otherwise it will be red. FILM COLLECT: The rear film sensor, when the film is sensed, it will turn grey, otherwise it will be red. BEPOWDER: Shaker powder position, film and powder weight sensor, when the powder on the film is heavy enough, it will turn grey, otherwise it will be red. -
Page 15: Operation Process
7. Begin to printer and once the film is moving forwards, press “Auto”. The system will enter full automatic mode. NOTE: The Adkins Inline 800 will begin to operate when two conditions are met. a) When the printed film is detected by the film input sensor b) the powder on the film is heavy enough to activate the weight sensor... - Page 16 8. When the film exits the dryer, place the film so that it can go under the film tension bar and then onto the take up unit. NOTE: This needs to be attached true and square or the film may skew. 9.
-
Page 17: Best Working Practice
5. Make sure that the film input sensor is clean and in the correct position for operation. DEFAULT SETTINGS. The required settings for the Adkins Inline Dryer will depend on several factors such as; Ink, film and the environment. A recommended base setting is shown below;... -
Page 18: Maintenance
MAINTENANCE Make sure dryer is switched off and cold before carrying out any maintenance. DAILY 1. At the end of operation, remove any excess powder that has landed outside the trough/shaker. 2. Any build up of oil/water vapour should be wiped clean with a cloth. 3. -
Page 19: Filtration System
FILTRATION SYSTEM The shaker is fitted with a three-stage filtration system. Stage 1: Air is drawn in through the upper exhaust inlet from the hood of the dryer, and passed down into the cooling zone at the bottom, where it will separate the oil from the exhausted air. Stage 2: The air will then pass through the carbon filter element, which will filter out fine particles. -
Page 20: Warranty
WARRANTY The Adkins Inline 800 is supplied with a 1 Year Manufacturer onsite parts and labour warranty. If you are within your warranty period and believe there is a fault with your equipment, please contact support@aadkins.com. The supplied warranty does not cover misuse, negligence or accidental damage. - Page 21 A. ADKINS AND SONS LIMITED DECLARATION OF CONFORMITY Application of Council Directives: European Low Voltage Directive (LVD), European Machinery Directive (MD), Electro Magnetic Conformity (EMC) Standards to which Conformity is (LVD): 60204-1:2018 Declared: (MD): EN ISO 12100:2010 2006/42/EC Annex1 (EMC):...
Need help?
Do you have a question about the INLINE 800 and is the answer not in the manual?
Questions and answers