Advertisement
Available languages
Available languages
EnGLIsH
For continuous operation, slide the switch toward the front of
the tool and press the forward part of the switch inward. To stop
the tool while operating in continuous mode, press the rear part
of the slider switch and release.
No‑Volt
The No-volt function stops the sander from restarting without
the switch being cycled if there is a break in the power supply.
Speed Control Dial (Fig. A)
The DCE800 sander is equipped with a variable speed control.
Adjust the speed by turning the speed control dial
control dial is numbered "1" through "5". The setting "1" is the
slowest speed (approximately 1200 RPM) and "5" is the fastest
speed (approximately 2400 RPM).
Use the higher speed settings for fast stock removal. Use
the lower speed settings to reduce removal rate for more
precise control.
Brush‑Type Skirt (Fig. C)
A brush-type skirt
12
surrounds the abrasive pad on the
DCE800. This skirt serves two purposes:
•
It extends below the surface of the abrasive pad to prevent
the abrasive from "gouging" the work.
•
It helps contain the drywall dust until the vacuum cleaner
pulls it away.
If the skirt is damaged or if it is worn excessively it should be
replaced by a D
WALT authorised service centre.
e
Expanding the Main Tube (Fig. E)
The main tube of the DCE800 can be expanded to various
desired lengths.
•
To expand the main tube, release the tube expansion
lever
8
and extend the tube to the desired length.
•
Close the tube expansion lever to lock the main tube
in place.
Attaching an AirLock™ Compatible Dust
Extractor (Fig. F)
Your drywall sander is compatible with the D
connection system. The AirLock™ allows for a fast, secure
connection between the AirLock™ connector
dust extraction port
7
.
1. Ensure the collar on the AirLock™ connector is in the unlock
position. (Refer to Fig. F.) Align notches
AirLock™ connector as shown for unlock and lock positions.
2. Push the AirLock™ connector onto the adapter
connector point.
3. Rotate the collar to the locked position.
nOTE: The ball bearings inside collar lock into slot and
secure the connection. The power tool is now securely
connected to the dust extractor.
nOTE: The sleeve of the dust extraction port can be
removed if damaged and replaced by the user. The sleeve is
available as an optional accessory and can be replaced using
a screwdriver.
38
Wireless Tool Control (Fig. A)
Your tool is equipped with a Wireless Tool Control transmitter
which allows your tool to be wirelessly paired with another
Wireless Tool Control device, such as a dust extractor.
To pair your tool using Wireless Tool Control, press and
hold the trigger switch
Control pairing button on the seperate device. An LED on the
4
. The speed
seperate device will let you know when your tool has been
successfully paired.
D
Optional Accessory
Your sander comes with mounting holes
for installing a D
install the tag. The D
locating professional power tools, equipment, and machines
using the D
the D
OPERATION
Instructions for Use
Proper Hand Position (Fig. G)
WALT AirLock™
e
Proper hand position requires one hand on the main handle
and one hand on the main tube
13
and sander's
Sanding Drywall (Fig. I)
14
on collar and
The drywall sander has an articulating sanding head. The head
can swivel in multiple directions, allowing the abrasive pad to
conform to the work surface. This action enables you to sand
the top, middle, and bottom of a wall or ceiling joint without
changing position.
1. Turn the vacuum cleaner switch ON (I).
2. Turn drywall sander switch ON.
3. Position the drywall sander lightly against the work surface.
CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the tool.
2
on the tool and the Wireless Tool
WALT Tool Tag Ready (Fig. H)
e
WALT Tool Tag. You will need a T15 bit tip to
e
WALT Tool Tag is designed for tracking and
e
WALT Tool Connect™ app. For proper installation of
e
WALT Tool Tag refer to the D
e
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
WARNING: To reduce the risk of personal injury, ALWAYS
wear a respirator approved for "Dust and Mist" and
connect the drywall sander to a suitable dust extractor.
Apply just enough pressure to align the sanding head with
the work surface.
15
and fasteners
WALT Tool Tag manual.
e
6
.
5
Advertisement
