Advertisement
Available languages
Available languages
g
Wear ear protection.
f
Wear eye protection.
Date Code Position (Fig. B)
The production date code
10
by a 2-digit week and is extended by a 2-digit factory code.
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Battery
1
Battery release button
2
ON/OFF slider switch
3
Speed control dial
4
Main handle
5
Main tube
6
Dust extraction port
7
Tube expansion lever
8
Sanding pad
9
Intended Use
This drywall sander is designed for professional
sanding applications.
Do not use under wet conditions or in the presence of
flammable liquids or gases.
This drywall sander is a professional power tool.
Do not let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
consists of a 4-digit year followed
WALT batteries and chargers.
e
1
is fully charged.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge, which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
. A combination of the three green LED lights will
16
illuminate, designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Attaching Sanding Discs (Fig. C)
Your DCE800 drywall sander is designed to use 225 mm
sanding discs
11
. Sanding discs for the DCE800 attach with
hook and loop.
The recommended sanding discs are available at extra cost from
your local dealer or authorised D
To Attach Sanding Disc to the Sanding Pad
(Fig. C)
1. Turn the sander over so that the sanding pad
facing upward.
2. Clean the dust from the sanding pad face.
3. Hold the pad with one hand to keep it from rotating.
4. With the other hand, center and place the sanding disc
directly on top of the pad. If using paper sanding discs,
ensure any ventilation holes in sanding disc align with
ventilation holes in sanding pad.
Slider Switch (Fig. D)
CAUTION: Hold the main handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops rotating.
Make sure the wheel has come to a complete stop be fore
laying the tool down.
nOTE: To reduce unexpected tool movement, do not switch
the tool on or off while under load conditions. Allow the sander
to run up to full speed before touching the work surface. Lift the
tool from the surface before turning the tool off. Allow the tool
to stop rotating before putting it down.
WARNING: Before connecting the tool to a power supply,
be sure the slider switch is in the off position by pressing
the rear part of the switch and releasing. Ensure the
slider switch is in the off position as described above after
any interruption in power supply to the tool, such as a
dead battery.
To start the tool, slide the ON/OFF slider switch
the front of the tool. To stop the tool, release the ON/OFF
slider switch.
EnGLIsH
2
and firmly pull the
WALT service centre.
e
9
is
toward
3
11
37
Advertisement
