Star S-LINK DLXT-121 Series Quick Install Manual

Thinline Auxiliary LED Lights
DLXT-121*** or DLXT-241***
(12 VDC) (24 VDC)
Quick Install Guide
GREEN
Pattern Select: Touch and release to ground to program
WHITE
Sync: Attach to White wires from other S-Link Lights for synchronization
GREEN w/WHITE
Split/Single: Connect with Black to Ground for Single Mode
Connect with Red to Switched Power for Split Mode
RED
Power: Connect to switched power
Warning BLACK
Ground: Connect to negative terminal of battery
Lights
ON/OFF
Switch
Use minimum
!
18AWG wire
-
BATTERY
12VDC or 24VDC
(depends upon model)
Pattern Programming and Synchronization
You can synchronize up to six
lights with compatibility.
DO NOT CONNECT WHITE WIRES
UNTIL PROGRAMMING HAS BEEN
COMPLETED FOR ALL LIGHTS!!
1. Power up the first unit and select a
Phase 1 pattern. Touch and
release the green wire to ground to
change patterns.
2. Program the second light with
the same Pattern Type.
Lights with the SAME phase
flash together (simultaneous).
Lights with DIFFERENT phases 10
flash opposite one another
(alternate).
Pattern Shortcuts: Hold Green wire to ground for indicated
time.
3. After programming all lights, tie
Steady Burn: Not in pattern cycle. Only accessible through
off the green wires and connect
the white wires together.
4. Test lights by applying power to all of them at the same time.
Alternating Pattern Simultaneous Pattern
(Programmed for opposite Phases) (Programmed for same Phase)
Light 1 Light 2 Light 1 Light 2
(ON) (OFF)
DLXT
DLXT-124*** or DLXT-244***
(12 VDC) (24 VDC)
Bezel
Rubber
Mounting
Gasket
Foam Compression Gasket
Mounting Surface
IMPORTANT
Pattern Description
Fast Singleflash (1.9 CPS)
1 11 A
2 12 B Flicker flash (1.7 CPS)
Post pop (1.4 CPS)
3 13 C
4 14 D PSU-flicker (0.4 CPS)
5 15 E
Random (1.9 CPS) (DEFAULT PATTERN)
6 16 F Quadflash (1.0 CPS)
7 17 G Quadflash
w/Post-Pop (1.0 CPS)
8 18 H Singleflash (1.0 CPS)
9 19 I Doubleflash (1.0 CPS)
Delta-Omega (0.3 CPS)
20 J
N/A Steady
(see below)
shortcut. Hold Green wire to ground for 18
seconds (light will flash 6 times).
Split Mode
In/Out Pattern Back & Forth Pattern
(Programmed for opposite Phases) (Programmed for same Phase)
Light 1 Light 2 Light 1
(OFF) (ON)
PLIT424WEB REV. A
• The installer must have a firm knowledge of basic electricity, vehicle electrical systems,
and emergency equipment.
• If you need to drill any holes when installing this light, please take care to check that
BOTH SIDES of your drilling surface are clear from obstructions, to ensure that you do
not damage your vehicle and or pre-existing wiring.
• Choose a mounting location away from any air bag deployment areas.
• Controls should be placed within convenient reach of the driver.
LED Array
• Use only soap and water when cleaning this product. Use of other chemicals may
discolor the lens and/or housing, thus diminishing the output of the light. Lenses that
have become discolored should be replaced immediately!
• DO NOT use a pressure washer to clean this light. Use of a pressure washer may
damage the light and WILL VOID THE WARRANTY.
• Keep LED modules and any radios as far away from each other as possible.
• Separate the radio wires and the LED wires.
• Any excess wires should be cut short.
Shortcut
• The Ground, Power, and Synchronization wires should be bound tightly together as
they run from light to light, through your switchbox, and finally to the battery.
• Do not ground each unit independently to the chassis. Run the ground for each unit
Pattern 1 :
(Phase 1)
in a "bus" like structure, to the negative terminal on the battery.
3 sec or 1 flash
Pattern 11 :
(Phase 2)
9 sec or 3 flashes
Pattern 6 :
(Phase 1)
6 Sec or 2 flash
Pattern 16 :
(Phase 2)
12 sec or 4 flashes
18 sec or 6 flashes
Programming Steady Burn Pattern in Single Mode:
1. Power the light up - Red wire to power
2. Hold Green wire to Ground until the light blinks six times (approximately 18 seconds),
then release it. The light should change to the Steady Burn pattern.
3. To exit Steady Burn pattern: Touch and release the Green wire to Ground.
Programming Steady Burn Pattern in Split Mode:
1. Power the light up (both Red and Green/White wire to power). Touch and hold the
Green wire to Ground until the light blinks six times (approximately 18 seconds), then
release it. One of the two halves will become steady, while the other flashes.
Light 2
2. To change the pattern on the flashing side, touch and release the Green wire to Ground.
3. To flip-flop the steady side and the flashing sides, hold the Green wire to Ground until
the light flashes 5 times (approximately 15 seconds) and then release it.
4. To exit Steady Burn pattern: Touch and release the Green wire to Ground.
2/1/24
Installation Notes
Wiring Notes
When wiring your lights, it is recommended that you take the following
precautions to reduce any Electromagnetic Interference (EMI).
Power MUST be applied to all synchronized lights
simultaneously. Excessive switch bounce or attempting to
power the units up independently will result in erratic operation.
Steady Burn Programming
Black wire and Green/White wire to Ground.
-2-